Printable Version of Topic

Posted by: FASTFATBOY May 9 2012, 01:16 AM

This system was installed on GM and High Tech Performance's STI Killer with a stock 10 bolt.

No idea on cost.

http://baer.com/products/full-floater-rear-conversion

http://www.gmhightechperformance.com/tech/suspension/ghtp_1111_sti_killer_improvements_searching_for_seconds_part_1/index.html


Also in the GMHTP article they refer to something called a "VeriSlide" for the rear, used in place of the Baer kit.

Posted by: roy May 9 2012, 03:32 AM

From reading the article , the Veri slide is a floating caliper bracket .

Posted by: wrencher May 13 2012, 12:56 AM

It says $1650 in the Baer link.
Not too far from a c-clip elimanated 12 bolt .

Posted by: Steve91T May 13 2012, 02:07 AM

Granted I have only done HPDE's and open track days, but why have I never experienced pad knockpad?

Posted by: Mojave May 13 2012, 04:09 AM

QUOTE (Steve91T @ May 12 2012, 09:07 PM)

Posted by: BPWilliams May 14 2012, 01:05 PM

Shoot you can pick up a new 9" full floater from Summit Racing for less than that....

Posted by: Major_Lee_Slow May 22 2012, 12:46 AM

All of the pad knock back issues I've had have 100% been attributed to worn hubs. I learned that it once the hub end play approaches 0.012 (measured at the tip of the wheel stud) it's time to replace the hub before pad knock back becomes an issue.

Posted by: 93FirehawkTA May 22 2012, 06:48 AM

This is interesting. I know I have massive pad knockback issues originating at my rear axle. For now though, I'll just adjust my driving style and remember to tap those brakes before the higher-speed braking zones...

Posted by: cozog May 22 2012, 01:46 PM

Maybe not a solution for everyone, but the installation of a Powertrax differential and Ten Factory axles completely eliminated the rear pad knock back due to c-clips. I also added 2psi brake check valves in both front and rear lines.
Can't do much about worn out front hubs though, except replace.
Hope this helps.

Posted by: 93FirehawkTA May 25 2012, 01:16 AM

Maybe I'm dreaming, but I believe there are some type of springs that can be installed on the pistons to counteract the knockback. Sure you get some pad drag on the rotor, but it's way better than entering the braking zone at 150, in traffic, and the brake pedal going almost to the floor. Anyone used something like this before?

Posted by: GlennCMC70 May 25 2012, 02:55 AM

Anti knockback spings.
http://www.hrpworld.com/index.cfm?form_prod_id=4856&action=product

http://www.apracing.com/Info.aspx?InfoID=110&ProductID=7

http://www.nasaforums.com/viewtopic.php?f=3&t=31588

http://www.knsbrakes.com/AP8350.php

http://www.google.com/#hl=en&gs_nf=1&gs_mss=Brake%20caliper%20anti&cp=36&gs_id=31&xhr=t&q=Brake%20caliper%20anti%20knockback%20springs&pf=p&sclient=psy-ab&oq=Brake+caliper+anti+knockback+springs&aq=f&aqi=&aql=&gs_l=&pbx=1&bav=on.2,or.r_gc.r_pw.r_qf.,cf.osb&fp=dd482f42f1055179&biw=1421&bih=853

Posted by: rocktman1 May 26 2012, 02:01 AM

Springs seem like a neat idea. I wonder how they'd increase pad wear, and rotor heat (since the rotor couldn't cool off with constant friction).