Fall is slow, gotta pay some bills. Shook the shop down and this stuff found its way onto my workbench.

BBK 58mm throttle body for LT1. includes IAC/TPS sensors. I ran this on Aeromaro for most of its racing years. Works fine, won its last race. New from Summit is $330, how about $180 $160 shipped to US lower 48. TB SOLD

(IMG:http://www.blainefabrication.com/projects/2011_10_04/IMG_4556.JPG)

(IMG:http://www.blainefabrication.com/projects/2011_10_04/IMG_4557.JPG)

Crane Gold roller rockers, set of 8, 1.6 ratio. These are the wide body rockers, use with 7/16" studs. They were part of the DRM build of my LT1, but were too close to the big dia springs for my comfort so I replaced them with CC, and carried these as spares. All of the rollers are free, bearings good. 2 of the tips have a noticeable flat spot, pic is of the worst one. The other 6 tip rollers are fine. Summit lists the set of 16 for $470, how bout $110 $90 $70 shipped to US lower 48

(IMG:http://www.blainefabrication.com/projects/2011_10_04/IMG_4559.JPG)

(IMG:http://www.blainefabrication.com/projects/2011_10_04/IMG_4561.JPG)

Set of 8 polylocks for 7/16" studs. Complete with set screws Excellent condition, no boogers. Looks like a new set of 16 runs $55-80, how about $20 $15 $10 shipped to the lower 48.

(IMG:http://www.blainefabrication.com/projects/2011_10_04/IMG_4562.JPG)

Tilton LS flywheel for 7.25" clutch. Steel, new. Tilton app charts lists it for all C5 and C6, also fits Fbody. It is new, I got 2 of them with the C5 Vette boxcar, the eventual buyer will only need one. Summit list is $723, how bout $560 plus shipping. Did I mention it's new, never installed? I'm a Tilton dealer, could put together a package for you with matching clutch pack, TOB, etc.

(IMG:http://www.blainefabrication.com/projects/2011_10_04/IMG_4563.JPG)

(IMG:http://www.blainefabrication.com/projects/2011_10_04/IMG_4564.JPG)

This post has been edited by Blainefab: Apr 15 2012, 08:07 PM

Ref the TB. This is a good unit, and I have this one on my 440 wheel hp LT1. Nice piece.

They do have one annoying problem that Alan can easily fix (he may have already). The shaft which actuates the butterflies can work loose from the throttle cable mount bracket...the thing the cable attaches to. This usually creates either an idle problem, or a WOT problem or both. One or two spot welds on shaft connection will fix this.

And that is a smoking deal if you need more air to go with your fuel.

This one has stayed tight, but I'd be glad to add some pre-emptive tacks for the buyer

(IMG:http://www.blainefabrication.com/projects/2011_10_04/IMG_4566.JPG)

I confirmed that the dimensions match a LS1 Fbody flywheel, except the weight - 8# 5oz




This post has been edited by Blainefab: Apr 15 2012, 08:08 PM

Lowered prices, just in time for Halloween!

Throttle body is sold.

I lowered the price on the rockers and polylocks

I'll leave the price on the flywheel where it is for a week or so, then will raise it. I'm pretty sure I'll be able to use it someday, it's a nice piece.