 WTB: 1 front Koni, hollow 35(6)mm sway bar |
|
|||||||||
 Oct 26 2005, 06:46 PM
Post
#1
|
|
|
Advanced Member  Group: Advanced Members Posts: 588 Joined: 23-December 03 From: Sterling, IL Member No.: 7  |
Need 1 front Koni and a 35 or 36 mm front sway bar. (IMG:http://www.frrax.com/rrforum/style_emoticons/default/banghead.gif)
|
 |
 
|
 |
Replies
(1 - 9)
|
Oct 26 2005, 09:36 PM
Post
#2
|
|
|
Chapter 11 Racing Group: Advanced Members Posts: 1,166 Joined: 15-February 04 From: Houston, Republic of Texas Member No.: 207 |
I have a ST 35mm solid front bar. Also have 2 front Koni SA's, but they are still on the car and I lack the technical prowress to remove them without killing myself.
How soon do you need such things and would you even consider the solid 35mm bar? |
|
|
|
|
Oct 26 2005, 10:41 PM
Post
#3
|
|
|
Advanced Member Group: Advanced Members Posts: 588 Joined: 23-December 03 From: Sterling, IL Member No.: 7 |
Whoops, I should say a Koni DA. The other three I have are DA's. As for the bar, thanks for the offer, but I'll pick up a new hollow 35 if I can't find one used.
|
|
|
|
|
Oct 26 2005, 11:34 PM
Post
#4
|
|
|
On vacation. Group: Vacationing Posts: 28 Joined: 23-October 05 Member No.: 940 |
I have a 35mm hollow bar for 4th gens for $125 plus shipping including the end links with the harder durometer "white" rubber bushings...I have a set of DA Konis revalved for road racing with springs installed (just bolt them into your car) - $400 for the set of two fronts..RP..plus UPS shipping on all items.
|
|
|
|
|
Oct 27 2005, 01:37 AM
Post
#5
|
|
|
No El-Use-O. Group: Advanced Members Posts: 2,368 Joined: 27-December 03 From: SW Michigan Member No.: 52 |
RP I'll take all of it. Shocks and swaybar.
|
|
|
|
|
Oct 27 2005, 04:00 AM
Post
#6
|
|
|
On vacation. Group: Vacationing Posts: 28 Joined: 23-October 05 Member No.: 940 |
Done...I'll email you the payment and shipping details...RP
|
|
|
|
|
Oct 27 2005, 04:03 AM
Post
#7
|
|
|
On vacation. Group: Vacationing Posts: 28 Joined: 23-October 05 Member No.: 940 |
Well, it looks like you'll have to contact me as the PM and Email features aren't working for me...email me at : robinsoncanyon@sbcglobal.net thanks, Richard
|
|
|
|
|
Oct 27 2005, 04:04 AM
Post
#8
|
|
|
On vacation. Group: Vacationing Posts: 28 Joined: 23-October 05 Member No.: 940 |
And, hey, I've got more hair than that photo..rp
|
|
|
|
|
Oct 27 2005, 09:48 AM
Post
#9
|
|
|
No El-Use-O. Group: Advanced Members Posts: 2,368 Joined: 27-December 03 From: SW Michigan Member No.: 52 |
Never mind Dick, I bought them from someone else. (IMG:http://www.frrax.com/rrforum/style_emoticons/default/biggrin.gif)
|
|
|
|
|
Oct 27 2005, 11:51 AM
Post
#10
|
|
|
Seeking round tuits Group: Advanced Members Posts: 5,522 Joined: 24-December 03 From: Kentucky Member No.: 33 |
I have a slightly "customized" Strano hollow 35 I could sell.
My car is a caster freak, or was before the pot hole incident. At 4.5 caster everything was fine, but at 5.6 on the driver side (stock/lowered) all aftermarket bars were a tight fit where they pass the shock. Even when I pulled everything back to 5.2 it was still tight for anything other than a 1LE bar. I finally put my old heavy ST35 solid bar back on because it provided slightly more shock clearance. Most cars can't get nearly that much caster without aftermarket control arms, so fit shouldn't be a problem. HOWEVER, I did try to gain a little clearance by heating a small section of the side of the bar where it passes closest to the shock, and squashing it on a press. The torch wasn't big enough for the job, so I just barely achieved a very faint dull red in an area no bigger than a quarter, and didn't gain more than a millimeter of clearance if that on the press (not sure I budged it at all). Of course, there is some paint damage, but since the heated area is close to the end I don't think there would be a strength problem. I've hesitated to list this bar for sale in it's current form, but if you're interested I'm sure we could agree on a reasonable price (IMG:http://www.frrax.com/rrforum/style_emoticons/default/wink.gif) This post has been edited by sgarnett: Oct 27 2005, 12:27 PM |
|
|
|
 |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
| Lo-Fi Version | Time is now: 2nd May 2025 - 09:00 PM |