New Member (Columbia, Maryland) - F-Body Road Racing and Autocross Forums

Hi, new to the handling scene and am pretty happy that I found you guys!!!

I'm been with the Drag racing crowd for the past couple years and finally realized that I actually need a car that I can drive everyday if I wanted and take highways exit ramps without slowing down to a snails pace since I'm scared to bend the 3.5" skinnies up front (no sway bar, so same case with street setup).

My power-band is probably not the best for road racing/autocross, but I hope to fix that in the near future with a cam swap but I just installed my suspension setup yesterday and am damn happy with the results! I can actually take turns fast!!!

As for my setup, it's a '94 Camaro Z28 with a LS1 (6.0ltr iron block) and T56 conversion. Here's the suspension setup:

- Koni adjustables front and back (4/4 kit from Strano)
- Strano front and rear sway bars
- Ground Control Coil over kit (550 in front, 175 in back)

This thing handles like it's on rails!!!! Feels a bit shaky going over bad surfaces, so subframe connectors are next! (I seriously can't belive I still don't have subframe connectors after all I've done!)

Sorry no pics of before after right now but I'll post some later when I get the car cleaned up and the ride height adjusted after the springs settle, but here's pics from the install :grin:

(IMG:http://img2.putfile.com/thumb/11/31422145358.jpg) (IMG:http://img2.putfile.com/thumb/11/31422145479.jpg)

(IMG:http://img2.putfile.com/thumb/11/31422145534.jpg) (IMG:http://img2.putfile.com/thumb/11/31422145550.jpg)

(IMG:http://img2.putfile.com/thumb/11/31422145566.jpg)

This post has been edited by Mean Green Z28: Nov 13 2007, 02:14 AM

Mean Green Z28 View Member Profile	Nov 12 2007, 04:17 PM Post #1
Member Group: Advanced Members Posts: 60 Joined: 11-November 07 From: Baltimore, Maryland Member No.: 2,000	Hi, new to the handling scene and am pretty happy that I found you guys!!! I'm been with the Drag racing crowd for the past couple years and finally realized that I actually need a car that I can drive everyday if I wanted and take highways exit ramps without slowing down to a snails pace since I'm scared to bend the 3.5" skinnies up front (no sway bar, so same case with street setup). My power-band is probably not the best for road racing/autocross, but I hope to fix that in the near future with a cam swap but I just installed my suspension setup yesterday and am damn happy with the results! I can actually take turns fast!!! As for my setup, it's a '94 Camaro Z28 with a LS1 (6.0ltr iron block) and T56 conversion. Here's the suspension setup: - Koni adjustables front and back (4/4 kit from Strano) - Strano front and rear sway bars - Ground Control Coil over kit (550 in front, 175 in back) This thing handles like it's on rails!!!! Feels a bit shaky going over bad surfaces, so subframe connectors are next! (I seriously can't belive I still don't have subframe connectors after all I've done!) Sorry no pics of before after right now but I'll post some later when I get the car cleaned up and the ride height adjusted after the springs settle, but here's pics from the install :grin: (IMG:http://img2.putfile.com/thumb/11/31422145358.jpg) (IMG:http://img2.putfile.com/thumb/11/31422145479.jpg) (IMG:http://img2.putfile.com/thumb/11/31422145534.jpg) (IMG:http://img2.putfile.com/thumb/11/31422145550.jpg) (IMG:http://img2.putfile.com/thumb/11/31422145566.jpg) This post has been edited by Mean Green Z28: Nov 13 2007, 02:14 AM

GlennCMC70 View Member Profile	Nov 13 2007, 04:53 AM Post #2
Veteran Member Group: Member Posts: 2,688 Joined: 23-December 03 From: Ft Worth, TX Member No.: 8	but i'm feeling the need to put skinnys on the front, DR's on the rear (315's) and swap the 250 rears for some stock cut springs. even at 230 hp, it should scream at 3200lbs! anyone seen my sponsor?

dailydriver View Member Profile	Nov 13 2007, 04:58 PM Post #3
Experienced Member Group: Advanced Members Posts: 1,528 Joined: 13-January 07 From: Solebury, Pa. Member No.: 1,589	QUOTE (Glenn98ZM6 @ Nov 12 2007, 11:53 PM) but i'm feeling the need to put skinnys on the front, DR's on the rear (315's) and swap the 250 rears for some stock cut springs. even at 230 hp, it should scream at 3200lbs! anyone seen my sponsor? ^^^^ (IMG:http://www.frrax.com/rrforum/style_emoticons/default/icon_lol.gif) Glenn, you'll also need to dump that telephone pole front sway bar (and make sure you drive it around on the street like that, and then go on LS1TECH and swear up and down that it handles GREAT!! (IMG:http://www.frrax.com/rrforum/style_emoticons/default/lmao.gif) ).