|
||||
Oct 12 2007, 07:32 PM
Post
#1
|
|
|
Member ![]() Group: Advanced Members Posts: 211 Joined: 22-February 06 Member No.: 1,085 |
I have several LCA/PHR reducer/spacers made up and ready to go.
They are made from 4140CM and fit the XM 3/4" Rod Ends that many are using when making the Aluminum LCA/PHR set ups. You can use your stock bolts with this set up. $10 for each end, a LCA set would be 8 total pieces and would cost $40 shipped. If you do not need a full set we can work that out. PHR would be $20 shipped. This post has been edited by Herron Performance: Feb 6 2008, 01:51 PM |
|
|
|
![]() |
Feb 6 2008, 02:15 PM
Post
#2
|
|
|
newbie Group: Members Posts: 2 Joined: 5-February 08 Member No.: 2,105 |
Are the parts used for the PHB and the LCA's the same?
IE, I need the axle end for a pair of of LCAs and then both sides for a panhard bar. So can I order the $40 shipped set? IF so, where do I place the order? Thanks, Ryan |
|
|
|
Feb 6 2008, 02:27 PM
Post
#3
|
|
|
Member ![]() Group: Advanced Members Posts: 211 Joined: 22-February 06 Member No.: 1,085 |
The PHR and LCA parts are different sizes.
We can mix and match what you need. So you need 4 total LCA bushing/spacers and 4 total for the PHR. $40 shipped is right, I can take paypal at shon@herronperformance.com and just reference in there what you need or reference FRRAX thread. Let me know if you have other questions. SH Are the parts used for the PHB and the LCA's the same?
IE, I need the axle end for a pair of of LCAs and then both sides for a panhard bar. So can I order the $40 shipped set? IF so, where do I place the order? Thanks, Ryan |
|
|
|
Herron Performance DIY LCA/PHR Bushings/Spacers Oct 12 2007, 07:32 PM
RumbleZ I picked up some of these and got them in this wee... Nov 30 2007, 04:46 AM
sgarnett Cool, but why do you spring for CM for this applic... Nov 30 2007, 11:44 AM
Herron Performance QUOTE (sgarnett @ Nov 30 2007, 06:44 AM) ... Nov 30 2007, 04:44 PM
RumbleZ Well for me, these were readily available and sinc... Nov 30 2007, 04:14 PM
sgarnett QUOTE (RumbleZ @ Nov 30 2007, 11:14 AM) W... Dec 6 2007, 11:45 AM
Herron Performance Was my explantion sufficient?
QUOTE (sgarnett ... Dec 6 2007, 01:31 PM
Herron Performance I got more. Dec 14 2007, 01:20 PM
00 Trans Ram That's a good deal. When I made my LCAs, the s... Dec 14 2007, 02:25 PM
Herron Performance Yeah, the first sets i made were cutting up parts ... Dec 14 2007, 05:07 PM
infectus What about the rubber ends? I have the ones that r... Dec 18 2007, 03:29 AM
Herron Performance QUOTE (infectus @ Dec 17 2007, 10:29 PM) ... Dec 18 2007, 03:35 AM
infectus Yeah, the Rubber ends are the ones you are talking... Dec 18 2007, 03:47 AM
slowcamaro QUOTE (Herron Performance @ Dec 17 2007, 10... Dec 18 2007, 04:49 AM
Herron Performance The rubber ends I used I *THINK* did need a reduce... Dec 18 2007, 12:36 PM
infectus The rubber ends I used had to have a reducer put i... Dec 18 2007, 02:55 PM
00 Trans Ram The stock bolts are 12mm, I think. 1/2" = 12.... Dec 18 2007, 07:32 PM
slow paypal sent. Feb 6 2008, 04:09 PM
Herron Performance Still have several of these. Apr 10 2008, 06:37 PM
Gregg_98TA QUOTE (Herron Performance @ Apr 10 2008, 01... Apr 24 2008, 12:38 PM
Herron Performance QUOTE (Gregg_98TA @ Apr 24 2008, 06:38 AM... Apr 24 2008, 12:43 PM
roadracetransam QUOTE (Gregg_98TA @ Apr 24 2008, 05:38 AM... Apr 24 2008, 08:59 PM
Herron Performance Still have some of these!!
So when you wea... Jun 6 2008, 05:28 PM
Herron Performance Got more! Sep 23 2008, 06:49 PM
Herron Performance I got more of these sitting here, if you need them... Feb 9 2009, 03:09 PM
Herron Performance I need these gone, make offer!!!!
... Mar 19 2009, 08:31 PM
Herron Performance TTT May 20 2009, 06:11 PM
Herron Performance I still have some of these! Nov 5 2009, 09:54 PM![]() ![]() |
| Lo-Fi Version | Time is now: 16th November 2026 - 02:41 AM |