 Anyone used S & W racing for cages? |
|
|||||||||
 May 1 2008, 08:00 PM
Post
#1
|
|
|
Member  Group: Advanced Members Posts: 238 Joined: 17-February 04 From: Corpus Christi, Texas Member No.: 219  |
I talked to them and they have a 10 point DOM cage that would be NASA legal for 499 plus 160 for shipping. It is not complete. IT does not have petty bars for the door or some smaller bracing that I would add, but everything is notched and ready to go.
Any thoughts? |
 |
 
|
 |
Replies
|
May 1 2008, 08:33 PM
Post
#2
|
|
|
FRRAX Owner/Admin Group: Admin Posts: 15,433 Joined: 13-February 04 From: Ohio Member No.: 196 |
I put an S&W kit in my '89 formula. Yes, it's pre notched, no, it's not notched in the right places. I wound up cutting down and renotching almost everything in my kit. They are decent cages, but they do not fit terribly well (the A pillar area is the problem). If you can use everything else, go for it, but I really had issues with the A pillar fittment in my car.
|
|
|
|
Posts in this topic
ledfoot2 Anyone used S & W racing for cages? May 1 2008, 08:00 PM
CJ-TA QUOTE (ledfoot2 @ May 1 2008, 03:00 PM) I... May 1 2008, 08:20 PM ledfoot2 I don't have the unlimited funds and fancy tra... May 1 2008, 08:25 PM CJ-TA $4500 for everything...
Don't give me th... May 1 2008, 08:31 PM
Blainefab QUOTE (CJ-TA @ May 1 2008, 01:31 PM)... May 1 2008, 09:37 PM CJ-TA QUOTE (Blainefab @ May 1 2008, 04:37 PM) ... May 2 2008, 02:38 AM JaredT I know a guy who built a tube frame car with S... May 1 2008, 08:52 PM Glenn98ZM6 and being a LS1 car, its CMC2 for you. May 1 2008, 09:53 PM ledfoot2 Thanks for the info guys. If I had a good local c... May 1 2008, 11:57 PM Glenn98ZM6 Misty's car is an AI car. i don't know if ... May 2 2008, 02:54 AM mitchntx Chris, while you have given your builder the rule ... May 2 2008, 03:15 AM CJ-TA Mitch... You are right.. I haven't gone over t... May 2 2008, 03:55 AM mitchntx There are 2 guys currently in the greater Houston ... May 2 2008, 04:05 AM 00 Trans Ram Well, this will probably be taboo to say on this b... May 2 2008, 02:26 PM Glenn98ZM6 QUOTE (00 Trans Ram @ May 2 2008, 09:26 A... May 2 2008, 02:49 PM StanIROCZ Don't forget that steel prices have changed a ... May 2 2008, 04:43 PM trackbird QUOTE (Glenn98ZM6 @ May 2 2008, 10:49 AM)... May 2 2008, 05:54 PM Glenn98ZM6 they are called inspection holes for a reason. the... May 2 2008, 05:17 PM StanIROCZ QUOTE (Glenn98ZM6 @ May 2 2008, 01:17 PM)... May 2 2008, 08:49 PM Blainefab QUOTE (StanIROCZ @ May 2 2008, 01:49 PM) ... May 2 2008, 09:10 PM StanIROCZ QUOTE (Blainefab @ May 2 2008, 05:10 PM) ... May 2 2008, 10:38 PM ledfoot2 QUOTE (StanIROCZ @ May 2 2008, 03:49 PM) ... May 2 2008, 09:15 PM CMC #37 QUOTE (ledfoot2 @ May 2 2008, 04:15 PM) Q... May 2 2008, 09:41 PM StanIROCZ Oh, and I just remembered this. That one tube tha... May 3 2008, 03:30 PM mitchntx QUOTE (StanIROCZ @ May 3 2008, 10:30 AM) ... May 4 2008, 12:30 AM nape QUOTE (mitchntx @ May 3 2008, 07:30 PM) Q... May 4 2008, 03:31 PM CMC#5 ASTM513 specifies an increased yield strength of a... May 5 2008, 01:33 PM 00 Trans Ram Let's see - first off, good info about the ERW... May 5 2008, 02:34 PM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
| Lo-Fi Version | Time is now: 10th August 2025 - 12:10 PM |