 Anyone used S & W racing for cages? |
|
|||||||||
 May 1 2008, 08:00 PM
Post
#1
|
|
|
Member  Group: Advanced Members Posts: 238 Joined: 17-February 04 From: Corpus Christi, Texas Member No.: 219  |
I talked to them and they have a 10 point DOM cage that would be NASA legal for 499 plus 160 for shipping. It is not complete. IT does not have petty bars for the door or some smaller bracing that I would add, but everything is notched and ready to go.
Any thoughts? |
 |
 
|
 |
Replies
|
May 5 2008, 01:33 PM
Post
#2
|
|
|
Advanced Member Group: Advanced Members Posts: 902 Joined: 27-January 04 From: Magnolia, Tx. Member No.: 160 |
ASTM513 specifies an increased yield strength of almost 60% for DOM (type 5) over as rolled ERW (type 1). It also indicates, as you'd imagine, a lot closer tolerance control for OD, ID, ovality, etc etc. (tolerances cut in half in some cases!)
|
|
|
|
Posts in this topic
ledfoot2 Anyone used S & W racing for cages? May 1 2008, 08:00 PM
CJ-TA QUOTE (ledfoot2 @ May 1 2008, 03:00 PM) I... May 1 2008, 08:20 PM ledfoot2 I don't have the unlimited funds and fancy tra... May 1 2008, 08:25 PM CJ-TA $4500 for everything...
Don't give me th... May 1 2008, 08:31 PM
Blainefab QUOTE (CJ-TA @ May 1 2008, 01:31 PM)... May 1 2008, 09:37 PM CJ-TA QUOTE (Blainefab @ May 1 2008, 04:37 PM) ... May 2 2008, 02:38 AM trackbird I put an S&W kit in my '89 formula. Yes, i... May 1 2008, 08:33 PM JaredT I know a guy who built a tube frame car with S... May 1 2008, 08:52 PM Glenn98ZM6 and being a LS1 car, its CMC2 for you. May 1 2008, 09:53 PM ledfoot2 Thanks for the info guys. If I had a good local c... May 1 2008, 11:57 PM Glenn98ZM6 Misty's car is an AI car. i don't know if ... May 2 2008, 02:54 AM mitchntx Chris, while you have given your builder the rule ... May 2 2008, 03:15 AM CJ-TA Mitch... You are right.. I haven't gone over t... May 2 2008, 03:55 AM mitchntx There are 2 guys currently in the greater Houston ... May 2 2008, 04:05 AM 00 Trans Ram Well, this will probably be taboo to say on this b... May 2 2008, 02:26 PM Glenn98ZM6 QUOTE (00 Trans Ram @ May 2 2008, 09:26 A... May 2 2008, 02:49 PM StanIROCZ Don't forget that steel prices have changed a ... May 2 2008, 04:43 PM trackbird QUOTE (Glenn98ZM6 @ May 2 2008, 10:49 AM)... May 2 2008, 05:54 PM Glenn98ZM6 they are called inspection holes for a reason. the... May 2 2008, 05:17 PM StanIROCZ QUOTE (Glenn98ZM6 @ May 2 2008, 01:17 PM)... May 2 2008, 08:49 PM Blainefab QUOTE (StanIROCZ @ May 2 2008, 01:49 PM) ... May 2 2008, 09:10 PM StanIROCZ QUOTE (Blainefab @ May 2 2008, 05:10 PM) ... May 2 2008, 10:38 PM ledfoot2 QUOTE (StanIROCZ @ May 2 2008, 03:49 PM) ... May 2 2008, 09:15 PM CMC #37 QUOTE (ledfoot2 @ May 2 2008, 04:15 PM) Q... May 2 2008, 09:41 PM StanIROCZ Oh, and I just remembered this. That one tube tha... May 3 2008, 03:30 PM mitchntx QUOTE (StanIROCZ @ May 3 2008, 10:30 AM) ... May 4 2008, 12:30 AM nape QUOTE (mitchntx @ May 3 2008, 07:30 PM) Q... May 4 2008, 03:31 PM 00 Trans Ram Let's see - first off, good info about the ERW... May 5 2008, 02:34 PM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
| Lo-Fi Version | Time is now: 20th June 2025 - 10:11 AM |