Third Gen Camber Settings?? - F-Body Road Racing and Autocross Forums

Friends,

My 1987 IROC Z/28 is a dedicated race car. Trailered to the events and not street legal. Given that I drive on Goodyear GS-CS R Compound tires what is the best setting for the camber using stock strut mount plates??

I found some third-gen specs which state -1.75 is available using the stock plates and that is the recommeded settings for Road Racing.

I am headed off to buy a Camber tool to measure the settings and move mine in quite a bit. Does somebody have a quick howto on this?

I think the steps are: (from observing others on other cars, but I want to know the *REAL* fbody way to do this..)

1) jack up the front end, take off both front tires.
2) put the camber tool on the rotor
3) loosen the 3 upper strut bolts and bring the strut IN at the top toward the engine (using the tool to ensure 1.75 is setup. PERMANENTLY MARK the location of the plate with paint. (paint body/paint bracket so you can line them up later without the tool).
4) loosen the 3 upper strut bolts and take it to the max, measure and mark that, re-tighten the bolts.
5) mark several places along the strut tower with measurements on both sides so that you can play with settings during test and tune.
6) lower the car
7) try it and then try the different settings until you find what you like.

that is kind of MY process, is it right? what is missing?

what have you guys found that works best for autocross?

Brian

BrianChevy View Member Profile	Jun 7 2004, 07:50 PM Post #1
Member Group: Advanced Members Posts: 153 Joined: 3-January 04 From: Atlanta, GA Member No.: 90	Friends, My 1987 IROC Z/28 is a dedicated race car. Trailered to the events and not street legal. Given that I drive on Goodyear GS-CS R Compound tires what is the best setting for the camber using stock strut mount plates?? I found some third-gen specs which state -1.75 is available using the stock plates and that is the recommeded settings for Road Racing. I am headed off to buy a Camber tool to measure the settings and move mine in quite a bit. Does somebody have a quick howto on this? I think the steps are: (from observing others on other cars, but I want to know the REAL fbody way to do this..) 1) jack up the front end, take off both front tires. 2) put the camber tool on the rotor 3) loosen the 3 upper strut bolts and bring the strut IN at the top toward the engine (using the tool to ensure 1.75 is setup. PERMANENTLY MARK the location of the plate with paint. (paint body/paint bracket so you can line them up later without the tool). 4) loosen the 3 upper strut bolts and take it to the max, measure and mark that, re-tighten the bolts. 5) mark several places along the strut tower with measurements on both sides so that you can play with settings during test and tune. 6) lower the car 7) try it and then try the different settings until you find what you like. that is kind of MY process, is it right? what is missing? what have you guys found that works best for autocross? Brian

slowTA View Member Profile	Jun 9 2004, 02:15 PM Post #2
Experienced Member Group: Advanced Members Posts: 2,290 Joined: 4-May 04 From: Kenvil, NJ Member No.: 331	I think I saw that tool you need once. It bolts to 2 of the fender bolts and has a hook looking bolt with a turnbuckle between the 2 of them. The hook sits in the top of the strut mount so you can pull the strut mount towards the outside of the car, or loosen it and the mount slides towards the inside of the car. It doesn't look like that complicated of a tool to use or even make if you want to.