IPB

Welcome Guest ( Log In | Register )

 Forum Rules 
Unbalanced EngineeringUMI PerformanceHotpart.comBlaine Fabrication.comSolo Performance
> Short Circuit Protection, Between battery and battery cable.
GlennCMC70
post Jan 12 2011, 02:45 AM
Post #1


Veteran Member
*****

Group: Member
Posts: 2,688
Joined: 23-December 03
From: Ft Worth, TX
Member No.: 8



Anyone use something like this between your battery and main battery cable?
I'm sure 150 amps is not enough for a starter motor..... or is it?

http://www.amazon.com/Bussmann-Hi-Amp-Circ...s/dp/B0024JOKM4

I also thought these were interesting too.
http://compare.ebay.com/like/370336644693?...4=263602_309572
Go to the top of the page
 
+Quote Post
 
Start new topic
Replies
rocky
post Jan 13 2011, 01:46 PM
Post #2


Advanced Member
**

Group: Advanced Members
Posts: 412
Joined: 26-August 09
From: Mathews Va
Member No.: 6,032



I would want to do it so if the cable from the battery shorts to ground,1 the cab will not fill up with smoke from the melting cable (assuming the battery is in the pass. compartment), and 2 the battery will not blow up which is not fun and I would hate to be in the same compartment if that happened. So I would say we are protecting both car and driver for $50.

This post has been edited by rocky: Jan 13 2011, 01:48 PM
Go to the top of the page
 
+Quote Post

Posts in this topic
GlennCMC70   Short Circuit Protection   Jan 12 2011, 02:45 AM
GlennCMC70   http://cgi.ebay.com/200-AMP-12V-CIRCUIT-BR...5QQcm...   Jan 12 2011, 02:49 AM
trackbird   That's why I put a starter solenoid (think for...   Jan 12 2011, 03:25 AM
Mojave   On my C4 I used a 250 amp fuse on the cable to my ...   Jan 12 2011, 05:02 AM
cozog   QUOTE (Mojave @ Jan 12 2011, 12:02 AM) On...   Jan 12 2011, 06:27 PM
rocky   QUOTE (GlennCMC70 @ Jan 11 2011, 09:45 PM...   Jan 12 2011, 11:43 AM
GlennCMC70   Thanks guys. Also, you can download a PDF here. ht...   Jan 12 2011, 09:54 PM
85t5mcss   FWIW, most OE starters on SBCs run 70-90 Amp Draw....   Jan 13 2011, 01:12 AM
GlennCMC70   QUOTE (85t5mcss @ Jan 12 2011, 07:12 PM) ...   Jan 13 2011, 02:15 AM
85t5mcss   QUOTE (GlennCMC70 @ Jan 13 2011, 02:15 AM...   Jan 14 2011, 12:49 AM
trackbird   QUOTE (85t5mcss @ Jan 13 2011, 07:49 PM) ...   Jan 14 2011, 12:57 AM
trackbird   The dyno sheet where MSD tested my MSD mini starte...   Jan 13 2011, 02:54 AM
Mojave   QUOTE (trackbird @ Jan 12 2011, 08:54 PM)...   Jan 13 2011, 05:11 AM
trackbird   QUOTE (Mojave @ Jan 13 2011, 12:11 AM) QU...   Jan 13 2011, 04:22 PM
rocky   Every engine is a little different, I think I woul...   Jan 13 2011, 11:27 AM
mitchntx   I'm trying to figure out what were wanting to ...   Jan 13 2011, 12:55 PM
rocky   I would want to do it so if the cable from the bat...   Jan 13 2011, 01:46 PM
mitchntx   OK ... I can see that. So the cable shorting to g...   Jan 13 2011, 02:44 PM
rocky   Mitch good points and I know you know better safe ...   Jan 13 2011, 03:25 PM
mitchntx   Another thing ... and I'm sure I will be corre...   Jan 13 2011, 08:25 PM
Blainefab   QUOTE (mitchntx @ Jan 13 2011, 12:25 PM) ...   Jan 13 2011, 09:40 PM

« Next Oldest · General Discussion · Next Newest »
 

Reply to this topicStart new topic
2 User(s) are reading this topic (2 Guests and 0 Anonymous Users)
0 Members:

 



Lo-Fi Version Time is now: 16th June 2025 - 01:10 AM