 This pos clutch1, need input |
|
|||||||||
 Jun 6 2011, 02:31 PM
Post
#1
|
|
|
Experienced Member  Group: Advanced Members Posts: 1,099 Joined: 14-October 06 From: Mobile, Al Member No.: 1,410  |
A little history,
When I bought this car it had a bad throwout bearing. I fixed at, put in a used 25k mile stock clutch from a buddies car in it with a re surfaced flywheel and a GM slave. If you ran the car hard through the gears the clutch would stick on the floor in 3rd/4th. So I put a Tick master in the car, was ok for a while......after this last track event when you leave a stop light the clutch feels like it hangs up on release, slips as you let the pedal out, then when you shift the pedal is low and hard. Broken pressure plate? Bad slave? I bled the system, didn't help. What is a good stock replacement clutch? Don't need a flywheel, this one has less than 2500 miles since it was turned. If I am gonna go in there its getting a clutch and slave. Recommendations on a stock replacement clutch? |
 |
 
|
 |
Replies
|
Jun 15 2011, 01:17 PM
Post
#2
|
|
|
Experienced Member Group: Advanced Members Posts: 1,099 Joined: 14-October 06 From: Mobile, Al Member No.: 1,410 |
Update, I got an Autozone clutch kit complete with flywheel, tob, alignment tool. It's made by LUK. It is identical in appearance to the 2002 factory clutch I pulled out of the car (z06 unit).
Same exact markings by same maker, LUK. Got slave from Car Quest, an ap unit. Cost on clutch kit was $295, slave hydraulics $89. Drives like a dream now. This post has been edited by FASTFATBOY: Jun 15 2011, 01:20 PM |
|
|
|
Posts in this topic
FASTFATBOY This pos clutch1 Jun 6 2011, 02:31 PM
z28jeff I have a Sachs o.e. clutch kit in my 94 LT1. Been ... Jun 6 2011, 02:44 PM trackbird Do you have headers on the car? Jun 6 2011, 03:35 PM FASTFATBOY Stock exhaust, stock engine with free mods.
I fou... Jun 6 2011, 04:12 PM trackbird I'm guessing you could be boiling the fluid in... Jun 6 2011, 10:24 PM
FASTFATBOY QUOTE (trackbird @ Jun 6 2011, 10:24 PM) ... Jun 7 2011, 01:07 AM Blainefab QUOTE (FASTFATBOY @ Jun 6 2011, 06:07 PM)... Jun 7 2011, 08:09 AM FASTFATBOY Alan I am looking at c5 z06 clutches, f body tobs ... Jun 7 2011, 01:13 PM Eskimo I have a C5 Z06 clutch in my car, and have issues ... Jun 7 2011, 01:36 PM FASTFATBOY Eskimo, I shift my car around 5800 ish (5400 ish b... Jun 7 2011, 02:32 PM tonycook I've been using a Centerforce Dual Friction, F... Jun 8 2011, 01:47 AM FASTFATBOY I bought an autozone assembly tonight, this is a n... Jun 8 2011, 10:36 AM creeper whatever you do just don't buy anything clutch... Jun 8 2011, 05:23 PM Aardvark QUOTE (creeper @ Jun 8 2011, 10:23 AM) wh... Jun 8 2011, 06:13 PM FASTFATBOY Differences between Ac Delco and gm slave cylinder... Jun 8 2011, 07:41 PM Blainefab QUOTE (FASTFATBOY @ Jun 8 2011, 12:41 PM)... Jun 9 2011, 07:28 AM wrencher pretty sure the ZO6 PP was the standard replacemen... Jun 16 2011, 05:39 AM |
2 User(s) are reading this topic (2 Guests and 0 Anonymous Users)
0 Members:
| Lo-Fi Version | Time is now: 12th November 2026 - 03:01 PM |