 Rebuild my 208,000 mile rear, or a used low mile unit? |
|
|||||||||
 Jun 15 2012, 03:27 PM
Post
#1
|
|
|
Experienced Member  Group: Advanced Members Posts: 1,099 Joined: 14-October 06 From: Mobile, Al Member No.: 1,410  |
Since the 3000 mile whipping the car got on the Power Tour and the optima Faceoff the rear end sounds like a cement mixer.
What is my best option? I haven't torn into the rear end to inspect but will next week. With the miles I am afraid the axles are shot, I don't think its a good idea to use "axle saver" bearings as they move the bearings inboard and stress the axle face more. Rebuild bearing/seal kits are around $200. The gears with those miles should be ok, would you change them? Thanks in advance. |
 |
 
|
 |
Replies
|
Jul 17 2012, 05:12 PM
Post
#2
|
|
|
Experienced Member Group: Advanced Members Posts: 1,099 Joined: 14-October 06 From: Mobile, Al Member No.: 1,410 |
I put a temp gun on the yoke and the pumpkin after a spirited drive, 170 degrees.
I took it back apart and the new GM Yoke had a speedy sleeve looking deal with an oversize seal. So I took it off, used and old(new) seal with grey silicone on the back and pit it back together. Test drove it and is back on the rack, dry at the moment but seems to have to sit a while to show the leak. (IMG:http://i1122.photobucket.com/albums/l528/FASTFATBOY1/yoke.jpg) |
|
|
|
|
Jul 23 2012, 07:52 AM
Post
#3
|
|
|
I build race cars Group: Advanced Members Posts: 4,748 Joined: 31-August 05 From: Central coast, CA Member No.: 874 |
QUOTE (FASTFATBOY @ Jul 17 2012, 10:12 AM)  Test drove it and is back on the rack, dry at the moment but seems to have to sit a while to show the leak. Did this get fixed? If not, are you putting RTV on the splines of the yoke? I always do, and have had no problem with pinion seals leaking. |
|
|
|
Posts in this topic
FASTFATBOY Rebuild my 208,000 mile rear, or a used low mile unit? Jun 15 2012, 03:27 PM
trackbird If the welds on the axle tubes look ok (no cracks,... Jun 15 2012, 03:48 PM Blainefab QUOTE (FASTFATBOY @ Jun 15 2012, 08:27 AM... Jun 15 2012, 06:13 PM FASTFATBOY I ended up rebuilding my rear, here was the noise ... Jul 4 2012, 02:13 PM dailydriver ...and that's the bearing set that everyone sa... Jul 5 2012, 09:35 PM FASTFATBOY I have been fighting a leaking pinion seal since I... Jul 17 2012, 12:31 AM
dailydriver QUOTE (FASTFATBOY @ Jul 16 2012, 08:31 PM... Jul 17 2012, 08:22 PM ndtguy QUOTE (dailydriver @ Jul 17 2012, 01:22 P... Jul 23 2012, 02:13 AM Blainefab QUOTE (dailydriver @ Jul 17 2012, 01:22 P... Jul 23 2012, 07:50 AM StanIROCZ Does the pinion have preload? If you grab hold of... Jul 17 2012, 01:20 AM FASTFATBOY QUOTE (StanIROCZ @ Jul 17 2012, 01:20 AM)... Jul 17 2012, 02:04 AM StanIROCZ Normal operating temp is likely over 200F Jul 17 2012, 03:49 AM BPWilliams Yes I have a 180 deg cooling switch on mine and it... Jul 17 2012, 12:55 PM StanIROCZ QUOTE (BPWilliams @ Jul 17 2012, 08:55 AM... Jul 17 2012, 01:28 PM FASTFATBOY Didn't fix it, its not just leaking, its pouri... Jul 17 2012, 02:24 PM FASTFATBOY QUOTE (Blainefab @ Jul 23 2012, 07:52 AM)... Jul 23 2012, 01:10 PM ReEntryRacer I go along with Alan on the use of silicone sealer... Jul 27 2012, 05:42 AM StanIROCZ The factory uses pipe dope for the spine. Silicon... Jul 27 2012, 12:12 PM FASTFATBOY Car is fixed as of now, has been dry for a while n... Jul 28 2012, 12:38 AM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
| Lo-Fi Version | Time is now: 31st October 2025 - 09:18 AM |