 1/2" torque wrench - up to 150 ft/lb or 250 ft/lb? |
|
|||||||||
 Mar 11 2005, 06:29 PM
Post
#1
|
|
|
Member  Group: Advanced Members Posts: 195 Joined: 16-November 04 From: Toronto, Ontario, Canada Member No.: 543  |
I need to get a 1/2" torque wrench and was looking for some opinions. I have noticed that some go up to 150 ft/lb while others go up to 250 ft lb.
1) Is there anything on an f-body that would require any where close to 150? (I understand that they become less accurate as you approach the limits) 2) What are you opinions on husky vs craftsman? Would you even consider getting one of the Made in China cheapies? Thanks, |
 |
 
|
 |
Replies
|
Mar 11 2005, 06:37 PM
Post
#2
|
|
|
Scaring slow F body drivers with a VW diesel Group: Member Posts: 449 Joined: 23-June 04 From: Mt Gilead, Ohio Member No.: 376 |
I bought one when I replaced headgaskets on my (previously owned) Subaru. I am glad I bought the 250lb as I needed it for one set of bolts. Not sure if it is needed on a F-body but it is nice to have the extra just in case.
I bought a S&K. I did not want to put my trust in a cheap Chinese one. |
|
|
|
Posts in this topic
torontoZ28 1/2" torque wrench - up to 150 ft/lb or 250 ft/lb? Mar 11 2005, 06:29 PM
trackbird I had a Craftsman, the adjuster nut finally came l... Mar 11 2005, 06:37 PM bigshoe If I remember right, the ls1 crank pully needs to ... Mar 11 2005, 08:08 PM trackbird QUOTE (bigshoe @ Mar 11 2005, 03:08 PM)If I r... Mar 11 2005, 08:13 PM torontoZ28 now that you have mentioned the 20% figure as the ... Mar 11 2005, 08:30 PM trackbird I would buy the 150 ft lb first and then (if you e... Mar 11 2005, 08:45 PM torontoZ28 makes perfect sense. thanks for the advice. ill ... Mar 11 2005, 08:50 PM y5e06 QUOTE (trackbird @ Mar 11 2005, 12:37 PM)I ha... Mar 11 2005, 10:40 PM gillbot I got the Harbor Freight 150 ft-lb $10 specia... Mar 12 2005, 12:17 AM slowTA Put me down for a broken (kinda) Craftsman. The r... Mar 12 2005, 12:27 AM Jeff97FST/A QUOTE (y5e06 @ Mar 11 2005, 05:40 PM)QUOTE (t... Mar 12 2005, 01:00 AM trackbird QUOTE (y5e06 @ Mar 11 2005, 05:40 PM)QUOTE (t... Mar 12 2005, 04:49 AM torontoZ28 craftsman doesnt seem to have a good reliability r... Mar 12 2005, 07:25 AM Judd I've also had some bad luck with a Craftsman t... Mar 12 2005, 08:02 AM trackbird QUOTE (torontoZ28 @ Mar 12 2005, 02:25 AM)cra... Mar 12 2005, 02:02 PM Dave B Mike, stick with the 150 lb/ft unit. I use a crap... Mar 12 2005, 04:47 PM 00 Trans Ram I thought that Craftsman stuff was "guarantee... Mar 13 2005, 03:56 AM slowTA I used to work at Sears... all of the sockets are ... Mar 13 2005, 04:35 AM trackbird QUOTE (00 Trans Ram @ Mar 12 2005, 10:56 PM)I... Mar 13 2005, 04:38 AM y5e06 QUOTE (trackbird @ Mar 12 2005, 10:38 PM)QUOT... Mar 13 2005, 04:47 AM gillbot QUOTE (Judd @ Mar 12 2005, 02:02 AM)I've ... Mar 19 2005, 03:02 AM robz71lm7 I have an old craftsman 3/8" digitork that go... Mar 19 2005, 03:29 AM Judd QUOTE (gillbot @ Mar 18 2005, 10:02 PM)I had ... Mar 19 2005, 05:20 AM
gillbot Yessir!
Beings that I had 4 broken wrenches I... Mar 19 2005, 12:54 PM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
| Lo-Fi Version | Time is now: 31st October 2025 - 08:13 AM |