[trackbird]

I've decided to sell my 1991 Corvette M6. This is going to be a little long, but here's the scoop...(copied as I posted it on other forums, so this wasn't frrax specific):

I had a 1992 Z28 autocross car and I decided I wanted a street car. I pulled the engine out of the Z28 (approximately 1,200 miles on it since it was built) and bought a Corvette. I put a set of Trick Flow 175 heads on it and a TPIS Miniram II as well as a TPIS throttle body and did a complete teardown and refresh before putting it in the Corvette (rod/main bearings, had the crank polished, new cam bearings, all gaskets and seals, new heads, new intake, new throttle body). I bought a Canton road race pan for it, stainless works long tube headers and a Dewitt radiator and started putting it together. The transmission was converted to crash through and a Hurst shifter was installed. I also ordered all the weather stripping for it and changed some (the rest is in a box) as I had time. The heads, intake, clutch, flywheel and distributor have about 40 miles on them, the throttle body and injectors are less than that and I installed the Borla kit last weekend....it's brand new). I've paid for two proms from two reputable places and I've been working on cleaning up the tune and some driveablility issues and I'm finally tired of spending my time and money tuning it and not driving it. So...I'm listing it for sale. I have a pile of money in this car, I'm asking far less than I have in it and I'm not looking to go much lower on it. I don't have to get rid of it, but I think I'm going to go C6 shopping and send this to a good home. I'm selling the car and the collection of parts I have for it as a lot.

It's red with black leather and has 117 k miles on the chassis and a 6 speed with 3.45 gears (dual power seats, electronic climate controls).

I'll save time and just start a parts list:

350 bored .020 over with splayed main caps and two bolt studs (and a billet front bearing cap on the #1 main)
Forged crank (ZZ3 crank)
Lunati Street Race rods (5.7") with floating pins.
KB Signature Series 12cc dished pistons
Speed Pro plasma moly file fit rings
zero decked, torque plate honed and line bored.
Clevite bearings
Melling oil pump
Cloyes double roller chain
Comp cams 220/230 .510/.510 cam (114 lobe separation)
Comp roller lifters
Comp pushrods
Comp Cams chromoly 1.52 roller rockers (7/16" studs)
Moroso aluminum valve covers with a screw on cap TIG welded on
Trick flow 175 heads (10.49:1 counting decking, head gaskets and all)
ARP 7/16" rocker studs
ARP head bolts
ARP header studs
ARP oil pan, timing cover, etc bolts
ARP Pro series flywheel bolts
ARP harmonic balancer bolt
Jegs billet aluminum distributor hold down
TPIS Miniram II (1205 gasket)
Accell 36 lb/hr injectors
TPIS 58mm throttle body
Davis Unified ignition HEI distributor
MSD gear reduction starter
MSD plug wires
ATI lightweight aluminum Superdamper (3 ring, road race version with aluminum shell)
Aluminum adjustable timing pointer
Stainless works long tube headers (with air system removed and the holes TIG welded closed)
Cat delete pipe (bolt in using a band clamp on the front and the stock ball and socket rear flange)
Borla cat back (installed last weekend)
DeWitt 1.5" fabricated aluminum radiator
Hurst shifter (gearbox was converted to crash through)
Walboro 255 lph fuel pump (Racetronix kit)
Goodyear hoses
New power steering hoses and remanufactured pump
Alternator was replaced last month (reman from a parts store)
2 piece under drive pulley set
Edelbrock water pump
Fidanza aluminum flywheel
Centerforce dual friction clutch
New 275/40-17 Sumitomo summer tires (40 miles on them)
4 total sets of sawblades (3 painted, one machined finish)
J55 brakes (on the car)
Spare J55 caliper brackets
Spare ECM
Spare drive axles (rear, aluminum)
4 U joints for the rear axles (still in boxes)
New U joints in the driveshaft
Non crash through shift shaft from the ZF gearbox
Brembo "Sport" brake pads (on the car, and a set new in the box)
Metal Master brake pads (in a box)
New strap kit for mounting the rear axle U joints (still in a box)
Z51/Z07 springs (not on the car yet)
Stock shortblock (that came from this car)
Dana 44 clutch rebuild kit (new in the box)
4 brand new Koni sport adjustable shocks (still in the box, purchased last week)
Monroe Sensatrac shocks (on the car, 40 miles on those...give them to a friend or something)
Hypertech chip (came with the car, included with this package)
Accell 36 lb injectors (a second older set also included)
A box of weather stripping (the stuff I haven't installed)
Both tops (tinted and body color)
JVC in dash DVD player with hands free/bluetooth and Rockford rear speakers (fronts are in a box, I never got time to install those)
Hurst shift knob
AC has been converted to R134 (but I was planning to change it back to R12).

I'm sure there's more and I'll go through the garage and update this. I'd rather find someone who wants to finish the tune and enjoy it instead of parting it out.

So, in a nutshell, if you like tuning these cars and want a car with a lot of nice stuff in it and a bonus shortblock as well as 4 sets of wheels....look me up.

Pics on request.

Located on the west side of Columbus, OH.

trackbird (at) gmail dot com

$11,750