Who needs 3rd gen parts?, Placeholder thread to be updated regularly and soon Options

[trackbird]

What of the 25mm sway bar?
I'm also interested in the oil cooler if no one snags it.

The 25mm bar is still here.

The oil cooler is partially here. I took a sawzall to the hard lines to get it off of the car (moment of frustration). So, if you can locate new hard lines, I've got the actual cooler "block" and some of the hard lines (enough that you could possibly fabricate something or make it out of heater hoses).

Let me know if you need either of them.

Kevin, do you have the fuse panel cover?

The sound deadener panel that goes under the dash? I launched it into a dumpster since nobody seemed to want much of the interior stuff. If you're talking about something else, let me know, I still have some things, but I tossed the rest after getting sick of looking at it piled in the corner.

I think that's the one...kind of. It's the removable panel that hides the fuses.

Bummer. I had all of the stuff in a pile for a few weeks and finally decided to toss it all. I wish I'd known.

Sorry Dave.

[trackbird]

Ok, I'm adding a set of centerbolt valve covers. I bought these as prototypes from Canton. I was going to have 12 AN bungs welded onto them and get proper holes drilled for track use. However, I will probably change heads before then and figured I'd send these off to a good home. You'll need to gather up some hardware for them, they didn't come with any.

I paid $50 and a bit of shipping.

$50 + freight

Attached File(s)

 Picture_330__Small_.jpg ( 44.06K ) Number of downloads: 17

 

[trackbird]

25mm rear suspension techniques sway bar $90 + freight

Glassteck 2" cowl "bolt on" hood pending

A set of 1992 Z28 wheels (16" alloys, rough shape, but I think they are round enough for track wheels)

Factory oil cooler just the cooler and a section of hard line but not all of the lines, the lines are damaged/cut $20 + freight

I've also got an SLP takeout flywheel for an LT1/1 piece rear main seal engine. $50 + freight

Things that I'm still kicking around getting rid of:

T56/clutch/flywheel/bellhousing/B&M Ripper setup. Or, it might be packaged with the torque arm/crossmember stuff as well.

Holley Stealth Ram intake system. I think I'm going to change it out for a single plane EFI intake at some point.

I'd have a Holley Stealth Ram
24 lb SVO (I think) injectors
52mm throttle body (aftermarket, I forget which one)
MSD "dual connector" Pro-Billet distributor

I'm considering swapping to a carb for now and going back to EFI later. When I do the new EFI, I'm not going to use much of this stuff anyway, so I was thinking of selling it now, swapping over and then changing back later on.

Interested in the T56 set-up... Let me know when you are ready to sell.

Still interested? What's a full setup (clutch, flywheel, torque arm, crossmember, driveshaft loop, ripper, T56, bellhousing, I think that's all) worth? I'm keeping the master/slave cylinder and the pedals, the rest would pretty much be included.

I might be interested in the hood. Please email/post some pics of the actual hood once you get the car.

Was it you that E-mailed me? That machine died and I've not heard back from the person who was interested in the hood. I've got another guy interested, but I'm trying to figure out who was the first one to contact me?

What of the 25mm sway bar?
I'm also interested in the oil cooler if no one snags it.

Both are still here.

Do you still have the hood or have you sold it? Need one to replace the junk one thats on mine.

It's still here. Did you E-mail me? Someone did, but who?

Also, I'm adding the two stock TPI fans. I'm keeping the top shroud and I may or may not be able to part with the bottom mount (I forget if anything else is attached to it). $75 + freight for the pair of fans.

[Racerdad916]

I will call you this week. I am interested in the sway bar if no one claims it. I have a SUUUUUUPER sawz-all, and I am NOT afraid to use it......

[StanIROCZ]

Interested in the T56 set-up... Let me know when you are ready to sell.

Still interested? What's a full setup (clutch, flywheel, torque arm, crossmember, driveshaft loop, ripper, T56, bellhousing, I think that's all) worth? I'm keeping the master/slave cylinder and the pedals, the rest would pretty much be included.

Yes, still interested. I don't need the crossmember, torque arm, or driveshaft loop, but need everything else (or as much as you will sell me). What kind of clutch is it? 1pc rear main or 2pc flywheel? Everything else should include the trans and belhousing, complete clutch, flywheel, shifter, bolts, flywheel cover, and ??? As complete as possible will be easiest for me since I really don’t know what all I need.

How soon you looking to take it out? I'm planning to come down to Nationals so we could plan the exchange for then.

Out of curiosity, why a Richmond 5 speed? Lighter?

[trackbird]

Yes, still interested. I don't need the crossmember, torque arm, or driveshaft loop, but need everything else (or as much as you will sell me). What kind of clutch is it? 1pc rear main or 2pc flywheel? Everything else should include the trans and belhousing, complete clutch, flywheel, shifter, bolts, flywheel cover, and ??? As complete as possible will be easiest for me since I really don’t know what all I need.

How soon you looking to take it out? I'm planning to come down to Nationals so we could plan the exchange for then.

Out of curiosity, why a Richmond 5 speed? Lighter?

1 piece rear main flywheel.
Centerforce DF clutch (1k miles, 50 minutes on track, 2 autocrosses on it)
Bellhousing
Trans
B&M Ripper
Hurst Shifter Ball/Knob
Clutch fork

I think that's it.

I want to run a Richmond 5 speed for a few reasons.

I can't use 6th on a race track.
A Richmond 5 speed with 2.73's in the rear is almost a gear for gear match with a T56/3.42
Lower driveshaft RPM
It weighs 92 lbs
I can get a scattershield for it
I can use "standard" clutches

I'm sure there are others, but that's the bulk of them.

Depending on what the change over will cost and what we could work out on this will determine if I'm pulling it now or not.

[slowTA]

Kevin, do you have pics of the driveshaft loop?

[trackbird]

Kevin, do you have pics of the driveshaft loop?

It's attached to the crossmember. I don't have pics, but I could try to get some.