IPB

Welcome Guest ( Log In | Register )

 Forum Rules 
Solo PerformanceUMI PerformanceUnbalanced EngineeringHotpart.comBlaine Fabrication.com
 
Reply to this topicStart new topic
> New guy to the forum.
ChrisInUtah
post Jun 29 2016, 08:19 PM
Post #1


newbie


Group: Members
Posts: 12
Joined: 14-April 16
Member No.: 223,908



Hello All,
Signed up a little while ago and figured I would do my introduction. I have had three 4th gen Camaro's a 2000, 2001, and currently my 02' Z28. I have had my current one since 03' when I was stationed at Pope AFB NC. I did a few drag races there at Fayetteville track while I was in NC and ran a best of 12.8 at 109 with the car pretty much bone stock (lid and ported throttle). After Pope AFB I was stationed in Germany (05-07 and 09-12) I was about 40 min from Nurburgring and once I tried that track I said screw 1/4 mile crap. I focused on handling aspects of the car and left the power stuff mostly stock.

I separated the air force in 2013 and have been here in Utah since then. I just recently installed a cam/intake and supporting mods, and took the car down to the local drag and did a best of 13.9 with a nice high DA of 7800' with it being so hot that day. I don't have the car set up for drag at all, so although I am a little disappointed in the time, I can’t get too upset. I am looking to hit up the local race track here called Utah Motorsports Campus (formerly Miller Motorsports) but haven’t found anyone here who knows the ins and outs of the track yet to get a trip planned. I know there are plenty of great cars on here and my car is nowhere near setup like some of yours but here is a rundown of most of my current mods.

Current Mods/setup:
02 Artic White Z28, M6, T-top, LCA relocation, Adj LCA's, Adj TqArm, Panhard relocation, Adj Panhard, Shock tower brace, 3-point SFC, Road Race K-Member, Boxed Lower A-Arms, Solid Motor Mounts(All UMI) Strano Sway bars/Springs. Hooker LT, 3"True Dual with H-pipe, 1 chamber flowmasters, Monster LT1-S Dual Clutch, 233/239 TSP Cam, C5R Race Timing Chain, PRC Dual Springs, FAST 102, NW 102 TB, Turn One PS Pump, 2010 Camaro Brembo front brake swap....430HP/390Tq.
Thanks for the add, and I look forward to learning from you all!

- Chris

This post has been edited by ChrisInUtah: Jun 29 2016, 08:20 PM
Go to the top of the page
 
+Quote Post
dailydriver
post Jun 29 2016, 09:02 PM
Post #2


Experienced Member
***

Group: Advanced Members
Posts: 1,528
Joined: 13-January 07
From: Solebury, Pa.
Member No.: 1,589



WELCOME!


What dampers (shocks)??

This post has been edited by dailydriver: Jun 29 2016, 09:04 PM
Go to the top of the page
 
+Quote Post
ChrisInUtah
post Jun 29 2016, 09:04 PM
Post #3


newbie


Group: Members
Posts: 12
Joined: 14-April 16
Member No.: 223,908



QUOTE (dailydriver @ Jun 29 2016, 09:02 PM) *
What dampers (shocks)??


Bilstein HDs
Go to the top of the page
 
+Quote Post
ChrisInUtah
post Jun 29 2016, 09:17 PM
Post #4


newbie


Group: Members
Posts: 12
Joined: 14-April 16
Member No.: 223,908



Here is a video from one of my Ring runs.

https://youtu.be/cUVv-tZIW1w

This post has been edited by ChrisInUtah: Jun 29 2016, 09:19 PM
Go to the top of the page
 
+Quote Post
ChrisInUtah
post Jun 29 2016, 09:29 PM
Post #5


newbie


Group: Members
Posts: 12
Joined: 14-April 16
Member No.: 223,908



(IMG:http://i1221.photobucket.com/albums/dd472/Chris28germany/Avatar.jpg)
Go to the top of the page
 
+Quote Post
BumpaD_Z28
post Jun 30 2016, 02:37 AM
Post #6


Advanced Member
**

Group: Advanced Members
Posts: 592
Joined: 16-October 06
From: Logan, UT
Member No.: 1,416



Hello, and welcome from Logan, UT !

Start with the UMC WOW +, days on Wednesdays .. THEN NASA UTAH :

http://www.nasautah.com/

~DaVe

This post has been edited by BumpaD_Z28: Jun 30 2016, 02:44 AM
Go to the top of the page
 
+Quote Post
trackbird
post Jun 30 2016, 11:01 AM
Post #7


FRRAX Owner/Admin
********

Group: Admin
Posts: 15,393
Joined: 13-February 04
From: Ohio
Member No.: 196



Welcome aboard! Looks like you have the car pretty well set up already. Was that done on stock heads or did I miss them in your list (I read it a couple times, but it's early).
Go to the top of the page
 
+Quote Post
ChrisInUtah
post Jun 30 2016, 02:13 PM
Post #8


newbie


Group: Members
Posts: 12
Joined: 14-April 16
Member No.: 223,908



QUOTE (trackbird @ Jun 30 2016, 05:01 AM) *
Welcome aboard! Looks like you have the car pretty well set up already. Was that done on stock heads or did I miss them in your list (I read it a couple times, but it's early).


Yes, I still have the stock 241 heads on.
Go to the top of the page
 
+Quote Post
trackbird
post Jun 30 2016, 02:32 PM
Post #9


FRRAX Owner/Admin
********

Group: Admin
Posts: 15,393
Joined: 13-February 04
From: Ohio
Member No.: 196



That seems like really impressive amounts of power from stock heads. Not that it's a little cam, but that's still good output.
Go to the top of the page
 
+Quote Post

Reply to this topicStart new topic
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:

 



Lo-Fi Version Time is now: 28th March 2024 - 07:26 PM