New member - here from New Jersey - F-Body Road Racing and Autocross Forums

Hi guys. I recently became aware of this whole board via some friends of mine on thirdgen.org. This looks like a good forum for me to be on and I am hopeful to learn as much as I can by reading some of the forums. I will make sure to search for the info I have questions on, and I will always keep things tech related.

I've had my 1987 IROC for 21 years now and it was my high school car. Years later after I made it look real nice, I got bit by the quest for more performance. The car is indeed a true real-deal street car that I use for autocross, short course road racing, drag racing, car shows, and general street duty. I do not own a trailer and street drive it wherever I go. My parts selection is based on those factors, so I have quite the balancing act to do when it comes to picking parts.

I have competed in the Optima Batteries Search for the Ultimate Street Car series in 2016 and also in 2017 (both at New Jersey Motorsports park)
I have also competed in the UMI Performance Autocross challenge in 2019 and 2020.
I also have done a handful of other autocross events in NJ and PA as well.

I enjoy the heck out of the car, but I know it will never be competitive in any specific CAM-T class or competition. For me, it is all about building/driving the car to find its potential, and then learning what I can do to take it a step further.

As mentioned, its an 1987 IROC-Z. It has a 406 small block chevy with a dart block, dart heads, callies rotating assembly, full roller valvetrain, and I use the holley sniper efi. I know the automatic trans is not optimal, but it is what is staying in the car. it consists of a ProBuilt Automatics 700R4 built with their tiop level package, and a 9.5" Edge Racing 3,400 converter. A 3" driveshaft from Dennys, and a Moser 12 bolt rear axle with 33 spline axles nad a tru Track. It currently has 3.55 gears, but In February it will get a gear change from 3.55 to 3.91 gears. Also, the engine was built with nitrous in mind and it will indeed be getting a 150-200 wet shot soon.

Front:
I have the C4 HD 13" brake package up with Hawks HPS pads. UMI A-arms up front with Koni Yellow struts and UMI upper strut mounts. OEM sway bar with poly mounts. Replacement Moog springs and a 2" drop-spindle setup. Replaced everything to the steering system with new components and had the original IROC-Z steering box re-built this past winter so it is very on-point. Wheels are 18x8" with a Nitto 555 255/40/18 tire that I would love to replace.

Rear:
UMI adjustable lower control arms, UMI panhard bar, Founders performance upper panhard bar. OEM swaybar with poly mounts. Koni yellow rear shocks. Moog springs with 3/4 coil cut off. C4 rear brake conversion so 12" rotor with powerstop pads. 18x10" wheel with a 285/40/18 nitto 55 tire. Also looking to replace these in the spring.

Here are some photos:

(IMG:https://live.staticflickr.com/4354/37099178212_179dd3ccc4_c.jpg)

(IMG:https://live.staticflickr.com/65535/49900080406_c0efef3152_c.jpg)

(IMG:https://live.staticflickr.com/65535/49899561173_f239747cee_c.jpg)

(IMG:https://live.staticflickr.com/65535/50269531676_c369c0fe6d_c.jpg)

(IMG:https://live.staticflickr.com/7113/27355806591_71c8967ff4_c.jpg)

(IMG:https://live.staticflickr.com/4445/37713056722_a617e759f7_c.jpg)

(IMG:https://live.staticflickr.com/65535/50055682841_ddbb67f597_c.jpg)

here is a link to some of my photo albums of events and my car's build over recent years:
https://www.flickr.com/photos/iroczman15/albums

I also have a youtube channel, and while I do not do any editing or creative video work, I do have some videos of my autocross runs over recent years. if you search through the "My videos" section. My username is the same as it is here IROCZman15

I am also on www.thirdgen.org using this username and I have a couple of long "build" threads and some racing info there along with photos, datalogs, videos, and tech info.

Glad to be a member here and looking forward to what I can learn after I spend some time reading.

IROCZman15 View Member Profile	Jan 6 2021, 04:33 PM Post #1
newbie Group: Members Posts: 28 Joined: 5-January 21 From: Roxbury, NJ Member No.: 231,208	Hi guys. I recently became aware of this whole board via some friends of mine on thirdgen.org. This looks like a good forum for me to be on and I am hopeful to learn as much as I can by reading some of the forums. I will make sure to search for the info I have questions on, and I will always keep things tech related. I've had my 1987 IROC for 21 years now and it was my high school car. Years later after I made it look real nice, I got bit by the quest for more performance. The car is indeed a true real-deal street car that I use for autocross, short course road racing, drag racing, car shows, and general street duty. I do not own a trailer and street drive it wherever I go. My parts selection is based on those factors, so I have quite the balancing act to do when it comes to picking parts. I have competed in the Optima Batteries Search for the Ultimate Street Car series in 2016 and also in 2017 (both at New Jersey Motorsports park) I have also competed in the UMI Performance Autocross challenge in 2019 and 2020. I also have done a handful of other autocross events in NJ and PA as well. I enjoy the heck out of the car, but I know it will never be competitive in any specific CAM-T class or competition. For me, it is all about building/driving the car to find its potential, and then learning what I can do to take it a step further. As mentioned, its an 1987 IROC-Z. It has a 406 small block chevy with a dart block, dart heads, callies rotating assembly, full roller valvetrain, and I use the holley sniper efi. I know the automatic trans is not optimal, but it is what is staying in the car. it consists of a ProBuilt Automatics 700R4 built with their tiop level package, and a 9.5" Edge Racing 3,400 converter. A 3" driveshaft from Dennys, and a Moser 12 bolt rear axle with 33 spline axles nad a tru Track. It currently has 3.55 gears, but In February it will get a gear change from 3.55 to 3.91 gears. Also, the engine was built with nitrous in mind and it will indeed be getting a 150-200 wet shot soon. Front: I have the C4 HD 13" brake package up with Hawks HPS pads. UMI A-arms up front with Koni Yellow struts and UMI upper strut mounts. OEM sway bar with poly mounts. Replacement Moog springs and a 2" drop-spindle setup. Replaced everything to the steering system with new components and had the original IROC-Z steering box re-built this past winter so it is very on-point. Wheels are 18x8" with a Nitto 555 255/40/18 tire that I would love to replace. Rear: UMI adjustable lower control arms, UMI panhard bar, Founders performance upper panhard bar. OEM swaybar with poly mounts. Koni yellow rear shocks. Moog springs with 3/4 coil cut off. C4 rear brake conversion so 12" rotor with powerstop pads. 18x10" wheel with a 285/40/18 nitto 55 tire. Also looking to replace these in the spring. Here are some photos: (IMG:https://live.staticflickr.com/4354/37099178212_179dd3ccc4_c.jpg) (IMG:https://live.staticflickr.com/65535/49900080406_c0efef3152_c.jpg) (IMG:https://live.staticflickr.com/65535/49899561173_f239747cee_c.jpg) (IMG:https://live.staticflickr.com/65535/50269531676_c369c0fe6d_c.jpg) (IMG:https://live.staticflickr.com/7113/27355806591_71c8967ff4_c.jpg) (IMG:https://live.staticflickr.com/4445/37713056722_a617e759f7_c.jpg) (IMG:https://live.staticflickr.com/65535/50055682841_ddbb67f597_c.jpg) here is a link to some of my photo albums of events and my car's build over recent years: https://www.flickr.com/photos/iroczman15/albums I also have a youtube channel, and while I do not do any editing or creative video work, I do have some videos of my autocross runs over recent years. if you search through the "My videos" section. My username is the same as it is here IROCZman15 I am also on www.thirdgen.org using this username and I have a couple of long "build" threads and some racing info there along with photos, datalogs, videos, and tech info. Glad to be a member here and looking forward to what I can learn after I spend some time reading.

mikedamageinc View Member Profile	Jan 7 2021, 01:21 PM Post #2
Advanced Member Group: Advanced Members Posts: 839 Joined: 14-February 10 From: Hampton Roads, VA Member No.: 8,551	Awesome car! Always cool to see a clean 3rd gen. I also agree with keeping cars multipurpose even though I tow my car to the track more for convenience, it is still a registered and inspected daily. It just doesn't seem as fun if I can't drive my track car to work! Have you ever made it down to VIR? There's a great group that I run with there (mustang group ironically, but really cool). There an event next month but too cold for me, I'll be there in April though.