IPB

Welcome Guest ( Log In | Register )

 Forum Rules 
Blaine Fabrication.comUMI PerformanceUnbalanced EngineeringHotpart.comSolo Performance
 
Reply to this topicStart new topic
00SSHarrison
post Apr 10 2011, 04:06 AM
Post #1


Member
*

Group: Advanced Members
Posts: 81
Joined: 14-February 11
From: Ottawa Ontario, Canada
Member No.: 51,098



Just some pics of the new parts for this season, new ACT clutch, Fidanza aluminum Flywheel, new B&M shifter, new moser center section, new UMI torque arm, relocation bracket, subframe connectors, front and rear sway bars, and front lower control arms, also installed new rear jegs performance rotors and hawk pads. First event is at Mosport in may, cant wait.

New Car Parts
Go to the top of the page
 
+Quote Post
SVTHuh
post Apr 14 2011, 09:45 PM
Post #2


Member
*

Group: Advanced Members
Posts: 207
Joined: 26-September 04
From: SoCal Baby!
Member No.: 472



Your going to be running a spool? Any reason for this??
Go to the top of the page
 
+Quote Post
Blainefab
post Apr 15 2011, 09:58 AM
Post #3


I build race cars
*****

Group: Advanced Members
Posts: 4,748
Joined: 31-August 05
From: Central coast, CA
Member No.: 874



What's the block in the rear bump stop mount-used for setup? If that's left on the car it may cause you problems.

(IMG:http://farm6.static.flickr.com/5030/5605140072_a92644f1d8.jpg)
Go to the top of the page
 
+Quote Post
Bud M
post Apr 15 2011, 03:05 PM
Post #4


Member
*

Group: Advanced Members
Posts: 181
Joined: 28-December 03
From: Sacramento
Member No.: 57



Looks great. But I'm curious why your center brace is "notched" so deep around the exhaust, looks like you could have run it straight across.
(IMG:http://farm6.static.flickr.com/5108/5604553843_2f7b287dcd.jpg)

This post has been edited by Bud M: Apr 15 2011, 03:07 PM
Go to the top of the page
 
+Quote Post
00SSHarrison
post Apr 16 2011, 06:13 PM
Post #5


Member
*

Group: Advanced Members
Posts: 81
Joined: 14-February 11
From: Ottawa Ontario, Canada
Member No.: 51,098



QUOTE (SVTHuh @ Apr 14 2011, 09:45 PM) *
Your going to be running a spool? Any reason for this??


No its a truetrac diff
Go to the top of the page
 
+Quote Post
00SSHarrison
post Apr 16 2011, 06:14 PM
Post #6


Member
*

Group: Advanced Members
Posts: 81
Joined: 14-February 11
From: Ottawa Ontario, Canada
Member No.: 51,098



QUOTE (Blainefab @ Apr 15 2011, 09:58 AM) *
What's the block in the rear bump stop mount-used for setup? If that's left on the car it may cause you problems.

(IMG:http://farm6.static.flickr.com/5030/5605140072_a92644f1d8.jpg)


Im trying out a couple of different set ups for bump stops, when i ordered my 9" housing from moser i got the oil fill spout on the rear and its the first thing to bottom out so i might have to cut it off and cap it to get my full travel back

This post has been edited by 00SSHarrison: Apr 16 2011, 06:20 PM
Go to the top of the page
 
+Quote Post
00SSHarrison
post Apr 16 2011, 06:17 PM
Post #7


Member
*

Group: Advanced Members
Posts: 81
Joined: 14-February 11
From: Ottawa Ontario, Canada
Member No.: 51,098



QUOTE (Bud M @ Apr 15 2011, 03:05 PM) *
Looks great. But I'm curious why your center brace is "notched" so deep around the exhaust, looks like you could have run it straight across.
(IMG:http://farm6.static.flickr.com/5108/5604553843_2f7b287dcd.jpg)


Ya im switching it out for the flat one, its way close to the ground
Go to the top of the page
 
+Quote Post
SVTHuh
post Apr 16 2011, 09:27 PM
Post #8


Member
*

Group: Advanced Members
Posts: 207
Joined: 26-September 04
From: SoCal Baby!
Member No.: 472



QUOTE (00SSHarrison @ Apr 16 2011, 01:13 PM) *
QUOTE (SVTHuh @ Apr 14 2011, 09:45 PM) *
Your going to be running a spool? Any reason for this??


No its a truetrac diff



Oh, Sweet.. It just looked an aweful lot like at spool.. lol.
Go to the top of the page
 
+Quote Post

Reply to this topicStart new topic
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:

 

Lo-Fi Version Time is now: 3rd June 2025 - 12:09 PM