IPB

Welcome Guest ( Log In | Register )

 Forum Rules 
UMI PerformanceSolo PerformanceUnbalanced EngineeringBlaine Fabrication.comHotpart.com
 
Reply to this topicStart new topic
> Top or bottom
KCG
post Sep 15 2017, 10:40 AM
Post #1


Member
*

Group: Advanced Members
Posts: 79
Joined: 2-August 13
From: Maryland
Member No.: 223,768



Pulling/dropping the eng/trans out of my 3rd gen soon. Whats the best way?
I've dropped them out of a 4th gen a few times and would do it that way again, but this is my first 3rd.
what say you ...
Go to the top of the page
 
+Quote Post
The Batman
post Sep 15 2017, 11:39 AM
Post #2


Member
*

Group: Advanced Members
Posts: 118
Joined: 30-October 11
Member No.: 120,269



QUOTE (KCG @ Sep 15 2017, 10:40 AM) *
Pulling/dropping the eng/trans out of my 3rd gen soon. Whats the best way?
I've dropped them out of a 4th gen a few times and would do it that way again, but this is my first 3rd.
what say you ...

I never had an issue going from the top of any of my 3rd gens. Heck, I had my 454 big block in and out of one of them more times than I can count. The 4th gen has the engine recessed much farther back, which makes going from the bottom easier than the top.
Go to the top of the page
 
+Quote Post
trackbird
post Sep 15 2017, 11:41 AM
Post #3


FRRAX Owner/Admin
********

Group: Admin
Posts: 15,393
Joined: 13-February 04
From: Ohio
Member No.: 196



He's right. I've even installed one with a 700R4 hanging on it (that's the hard way in case you were wondering). Just drop the trans, pull the radiator and lift the motor out of the top. Take the hood off to save some headaches. Just put an old blanket on the roof and lay it there. Watch the hood hinges, they can scratch the B pillar if you leave them on the hood (did that once).
Go to the top of the page
 
+Quote Post
KCG
post Sep 15 2017, 12:57 PM
Post #4


Member
*

Group: Advanced Members
Posts: 79
Joined: 2-August 13
From: Maryland
Member No.: 223,768



I should have stated I'm pulling eng/trans together, 305/T5.
Everyone still think its easier out the top?
Go to the top of the page
 
+Quote Post
BumpaD_Z28
post Sep 15 2017, 01:10 PM
Post #5


Advanced Member
**

Group: Advanced Members
Posts: 592
Joined: 16-October 06
From: Logan, UT
Member No.: 1,416



yep
Go to the top of the page
 
+Quote Post
slowTA
post Sep 15 2017, 01:42 PM
Post #6


Experienced Member
***

Group: Advanced Members
Posts: 2,276
Joined: 4-May 04
From: Kenvil, NJ
Member No.: 331



Top, I've pulled a SBC/T5 that way a few times and then also LS1/T56! Pulling the balancer off helps some too.

Another trick I've picked up is that you gain some breathing room by pushing the engine lift in from the side instead of the front. With the beaks on these cars it works surprisingly well.

https://photos.app.goo.gl/yYnvIuWINB7QXgqf1
Go to the top of the page
 
+Quote Post
KCG
post Sep 15 2017, 02:07 PM
Post #7


Member
*

Group: Advanced Members
Posts: 79
Joined: 2-August 13
From: Maryland
Member No.: 223,768



Thanks for that pic Chris.

I don't want to be a dumbass and not take everyones advice since I asked for it, but it just seems easier to me to not have to pull any of the engine apart, or wiring up top, or exhaust down below other than disconnecting from the cat.
Remove 6 k-member bolts and trans crossmember and everything just sits there as you lift the body. Obviously all the same hoses, lines, rad have to come out either way.
Someone talk me out of this! lol

I guess maybe the biggest fear I have is scratching the paint on install. This car is being pulled apart for a color change.
Go to the top of the page
 
+Quote Post
GCrites80s
post Sep 15 2017, 02:20 PM
Post #8


Advanced Member
**

Group: Advanced Members
Posts: 645
Joined: 30-January 15
From: Columbus, OH
Member No.: 223,855



People don't do the out-the-bottom thing on 3rd gens very often at all. Perhaps if they're changing the entire front suspension and K-member at the same time they might go bottom side.
Go to the top of the page
 
+Quote Post
nape
post Sep 15 2017, 02:23 PM
Post #9


Veteran Member
*****

Group: Advanced Members
Posts: 2,511
Joined: 14-November 04
From: Homer Glen, IL
Member No.: 540



I'd go out the top, done it a bunch of times. I wouldn't pull it with the trans though. The engine comes out nice and level without the trans. Once you have it ready to pull, the T5 is only 4 more bolts, and T5s are light.

It's way easier to install the trans with the clutch hydraulics hooked up too since the clutch alignment tools never get it perfect. Get trans up and to get it to slide the last 1/2", have someone push the clutch pedal. Done.
Go to the top of the page
 
+Quote Post
trackbird
post Sep 15 2017, 06:15 PM
Post #10


FRRAX Owner/Admin
********

Group: Admin
Posts: 15,393
Joined: 13-February 04
From: Ohio
Member No.: 196



QUOTE (KCG @ Sep 15 2017, 10:07 AM) *
Thanks for that pic Chris.

I don't want to be a dumbass and not take everyones advice since I asked for it, but it just seems easier to me to not have to pull any of the engine apart, or wiring up top, or exhaust down below other than disconnecting from the cat.
Remove 6 k-member bolts and trans crossmember and everything just sits there as you lift the body. Obviously all the same hoses, lines, rad have to come out either way.
Someone talk me out of this! lol

I guess maybe the biggest fear I have is scratching the paint on install. This car is being pulled apart for a color change.



Drop the trans out, it doesn't take that long. You have to pull the driveshaft, torque arm, crossmember and shifter anyway, pull the 4 bolts and pull the trans off of the back of the bellhousing and a few more bolts to knock the starter and bellhousing off (don't forget to pull the clutch slave cylinder off of the bellhousing). The trans is like 92 lbs, I used to drain the fluid, remove the bolts and just pull them out by hand and set them on my chest and then down under the trans tunnel (I was younger then). Pull the 4 nuts to drop the y pipe off of the engine and remove the radiator hoses and radiator, then pull the engine with the clutch and flywheel and balancer in place. An impact gun makes short work of the clutch and flywheel, but it will come out either way. Also, there are ground wires connected to the wiring harness and attached to some of the bellhousing bolts. You're going to want those loose before you start lifting the motor and find out that the harness is still attached solidly to it and now you're having issues getting to the bolts due to the cowl. It can be done, but it's "one more thing".

If you drop the K member, you have to deal with the brake lines. One of which is anchored to the k member under the oil pan (as I remember, it's been a while). I really don't think you'll find that to be easier, and then you get into tearing down the suspension. It's a lot of extra work.
Go to the top of the page
 
+Quote Post
slowTA
post Sep 16 2017, 12:20 AM
Post #11


Experienced Member
***

Group: Advanced Members
Posts: 2,276
Joined: 4-May 04
From: Kenvil, NJ
Member No.: 331



FYI, the engine leveler I have in the picture makes pulling the engine and trans together so much easier. It takes a little time and elbow grease to move it all the way, but that's obviously my opinion.

Also, if you drop the motor out the bottom don't forget the steering, sway bar, whatever those triangle supports are called that go from the crossmember to the frame, and the struts/springs are not coil overs. I might be wrong on this one but it will be a tight fit to get the motor passed the steering box.
Go to the top of the page
 
+Quote Post
CrashTestDummy
post Sep 16 2017, 02:20 AM
Post #12


Veteran Member
*****

Group: Advanced Members
Posts: 3,791
Joined: 3-July 04
From: Pearland, Texas
Member No.: 385



Engine leveler is a MUST. While I could see dropping, you have to have the brake lines pre-configured to do that, and deal with the struts and springs.
Go to the top of the page
 
+Quote Post

Reply to this topicStart new topic
2 User(s) are reading this topic (2 Guests and 0 Anonymous Users)
0 Members:

 



Lo-Fi Version Time is now: 28th March 2024 - 03:36 PM