![]() |
|
![]() ![]() |
![]() |
![]()
Post
#1
|
|
Advanced Member ![]() ![]() Group: Advanced Members Posts: 449 Joined: 13-February 04 From: DFW, TX Member No.: 195 ![]() |
I just got "wind" that when one rolls their fenders accomodate 315's (rub) that the paint will start showing cracks, after a period of time.
Are most in here, who run 315's, seeing this issue ? .....concerned future user. (IMG:http://www.frrax.com/rrforum/style_emoticons/default/smile.gif) |
|
|
![]()
Post
#2
|
|
Veteran Member ![]() ![]() ![]() ![]() ![]() Group: Member Posts: 2,688 Joined: 23-December 03 From: Ft Worth, TX Member No.: 8 ![]() |
you have to take a razor and cut the paint before you roll the lip. most of the paint on the lip will flake off, but shouldnt go beyond the cut you made prior to rolling. you've seen my car, and my fenders inner lip has been rolled.
|
|
|
![]()
Post
#3
|
|
Advanced Member ![]() ![]() Group: Advanced Members Posts: 827 Joined: 30-December 03 From: Bellevue WA Member No.: 73 ![]() |
I am running 315's and have yet to roll my fenders. the only time I have any rub issues is under HEAVY suspension loads.
But with the LG coil over kit coming, i may be rolling them to facilitate a lower stance. |
|
|
![]()
Post
#4
|
|
Seeking round tuits ![]() ![]() ![]() ![]() ![]() ![]() Group: Advanced Members Posts: 5,522 Joined: 24-December 03 From: Kentucky Member No.: 33 ![]() |
This is one of the things keeping me away from 315s. I suspect that there will also be some fatigue cracks in the rust-resistant zinc plating (a big deal for cars like mine that see salt).
I have heard that gently heating the paint with a blow dryer will help keep it from cracking. |
|
|
![]()
Post
#5
|
|
Advanced Member ![]() ![]() Group: Advanced Members Posts: 440 Joined: 25-December 03 From: Newport Beach, California Member No.: 41 ![]() |
i put about 10k miles on my car with rolled fenders... i didn't see any cracking... and i didn't take any special measures to keep it from happening...
i used a heavy piece of pipe wraped with duct tape to bash the fender lip into place.. and then later when an episode of axle hop shot my tire up into the fender lip and pulled it back down.. i just used some channel locks with rubber handles to smash it back in place... never had cracked paint... rocks chips are the real paint problem... don't forget, you actually looked at my car when you thought about buying it... you probably didn't even notice! mostly because the rest of the car looked great |
|
|
![]()
Post
#6
|
|
Experienced Member ![]() ![]() ![]() Group: Advanced Members Posts: 1,015 Joined: 28-December 03 From: Texas Member No.: 55 ![]() |
I have (had) some cracking in the fenderwell, but used touch up paint to seal it back up. It has held up so far, and made the crack, which was more like a chip, disappear.
|
|
|
![]()
Post
#7
|
|
Member ![]() Group: Advanced Members Posts: 162 Joined: 29-December 03 Member No.: 61 ![]() |
The lips on my car cracked in 2 or 3 places each side. Cracks were about 1 inch in length. Some paint chiped.
Used a hairdryer and don't think it did shit. Went over with several coats of touch-up. Still worth it! (IMG:http://www.frrax.com/rrforum/style_emoticons/default/biggrin.gif) |
|
|
![]()
Post
#8
|
|
Advanced Member ![]() ![]() Group: Advanced Members Posts: 449 Joined: 13-February 04 From: DFW, TX Member No.: 195 ![]() |
Thanks for all the responses.
...gives me a better idea of what I might (IMG:http://www.frrax.com/rrforum/style_emoticons/default/wink.gif) be getting into. |
|
|
![]()
Post
#9
|
|
Member ![]() Group: Advanced Members Posts: 176 Joined: 23-January 04 From: Fort Worth, Texas Member No.: 149 ![]() |
|
|
|
![]()
Post
#10
|
|
Experienced Member ![]() ![]() ![]() Group: Advanced Members Posts: 1,015 Joined: 28-December 03 From: Texas Member No.: 55 ![]() |
You don't need to mess up the fenders on that pretty bird Andrew. 315's are grossly over rated (IMG:http://www.frrax.com/rrforum/style_emoticons/default/cool.gif)
|
|
|
![]()
Post
#11
|
|
Advanced Member ![]() ![]() Group: Advanced Members Posts: 449 Joined: 13-February 04 From: DFW, TX Member No.: 195 ![]() |
What was I thinking.....you're right Chuck (IMG:http://www.frrax.com/rrforum/style_emoticons/default/rolleyes.gif)
(statement to throw Kyle off) (IMG:http://www.frrax.com/rrforum/style_emoticons/default/tongue.gif) |
|
|
![]() ![]() |
Lo-Fi Version | Time is now: 4th May 2025 - 07:12 PM |