Parting out:

1994 Ex World Challenge Camaro
(floorpan and firewall spec'd to AIX)
all fiberglas or plastic panels except for rear quarter panels
full roll cage
fiberglas dash panel
lexan front and rear
2 hoods
wing plus rear spoiler
Currie 9 in rear end, currie axles (31 spline) with 3.50 9 in nodular rear 3rd member
brake lines with wilwood proportioning valve
alum. gas pedal with morse style throttle cable
new front hubs and steering rack
oil and water overflow tanks
two sway bars - through frame mounting
alum. radiator mount
custom carb air box
alum air dam
splitter
22 gal fuel safe cell with braided line to fuel pressure regulator
$4400


355 c.i. short block
3 hrs since freshened
$900 work of block work:
(decked, honed lifter bores, polished lifter valley, lifter return breather tubes,
honed out and champhered oil return holes, flat tappet oil restrictor plugs)
Eagle forged crank and H beam rods, JE pistons (flat top 5.4cc valve relief)
block decked to .035 quench area with .039 fel Pro gasket
custom flat tappet cam ( approx 244/248 deg .547/.555 lift at 0.050 on 108 deg LSA)
7 in depth double kickout pan
Cloyes double roller chain and sprocket, front timing cover
Moroso hi volume oil pump
clevite 77 bearings, JE rings
$1650


Tremec TKO 600 transmission
0.82 5th gear
3 hrs on trans
$1450 SOLD

Dual MSD 6AL boxes with 2 MSD coils and wiring
$275 SOLD

Complete Brembo brake setup (calipers) with alum hats & rotors (13 in front/ 12 in rear with front mounting brackets and braided lines)
1 almost new set of Hawk 9012 pads plus one spare set about 50% worn.
$1450



Jerico transmission - 4 speed
1.78 1st gear
need to check on other ratios
1.0 4th gear
$2100

Dr. Gas custom exhaust system:
SLP ceramic coated mid length headers (1 3/4") opened up to 3 in exit with custom dr. gas frame clearance tubes with x pipe and ovalized 3 in tubes that exit by rear of doors - due to x-pipe and ovalized tubes being one unit this system cannot be shipped. Must be picked up or delivered. May split up system if it does not sell as unit.
$575

wheels:
as a set only
Forgeline 2 piece wheelset
(2) 17 x 9.5 with 7 1/2 in backspacing, (2) 17 x 11.0 with 8 in backspacing with 275 x 40 front and 315 x 35 rear tires
$675 correction on backspacing of 17 x 9.5 wheels. SOLD

CCW classics (polished)
(2) 17 x 11 with 8 in backspacing, (2) 17 x 12 with 8 in backspacing, also comes with additional outside rims (2) to change 17 x 12's to 17 x 11's with 315 x 35 front and 335 x 30 rear tires
$1100 SOLD




(2) JRZ double adjustable coil overs for front of Camaro - will try to supply spring rate you want if I have them in my stock of springs.
$650. note - these list for $1350 each. SOLD

Tilton aluminum bellhousing with hydraulic throw out bearing
$140

Comp stainless roller rockers - for 3/8 in stud in 1.6 ratio - pro magnum model - not self aligning (i.e. requires guide plates)
$125 SOLD

More parts:
Stack Data Aquisition Guage model ST8100 ( this may be an M model as display indicated predicitve lap timing but without beacon I am not positive)
ser # 11631
with all wiring to senders/ignition. has low oil pressure warning light in unit.
and the following sending units:
water temp, oil pressure, fuel pressure
needs oil temp sender.
has lap time module and receiver but does not have transmitter beacon.
with manual
$675 (retail this unit with senders goes from $ 1700) SOLD

Griffin race radiator - 27.5 x 19 x 3 (2 row) -used for 1 race day. like new
with dual electric fans Griffin part # 55242X
$200 SOLD

Forgeline wheels (2) 17 x 9.5 - ( 7 1/2 in backspacing) 2 piece with 275x 40 x 17 DOT tires with approx 15 heat cycles. same price with or without tires. SOLD
$275

CCW classic polished wheels (2) 17 x 11 (7 1/2 in backspacing) 3 piece with 315 x 35 x 17 DOT tires with approx 6 heat cycles
used for one race season. same price with or without tires.
$ 675



Plus shipping

Please send all questions to consultjr@msn.com
or call me at 801-979-3739

Thanks,

J.R.

I am interested in:

all fiberglas or plastic panels == are they fiberglass nose and fenders?

wing plus rear spoiler == is it a current/modern SWCGT wing style, or just a spoiler?

Currie 9 in rear end, currie axles (31 spline) with 3.50 9 in nodular rear 3rd member ==is it a full floater? any more details....

splitter == any pics of this?

CCW wheels == what size, style, color

JR, sorry to hear you're parting out the car. Too bad it didn't sell intact.

Chris and I are debating the transmission.

Randy, I recall the splitter being quite stout. I've got a picture around here somewhere....

Jason

I may be interested in just the Chassis........ Email sent

Randy, pics of the bumper cover are on this page:

http://www.z28racergirl.com/gallery2/main....6&g2_page=4

Jason

Jason,

If interested call me. I have a special Christine/Jason deal.

J.R.

JR, (or maybe anyone else):

The tremec 600--is that a synchromesh tranny? I know the Jericho is not. AI rules are I have to run synchros. Sorry I forgot to ask on the phone a moment ago.

Thanks,
Christine

I want the CCW's with tires.

How much with shipping to 37087?



And what spacers, if any, are needed for them?

You say 8 inch backspacing. When I bought mine they called the offset 46mm I believe. Are these the same? Otherwise I have to go measure mine at home....

Since Randy asked about these first, I'll wait and see what he decides first.

I'm still curious about the spacers...

If they are the same offset as mine, I use thin 1/4" spacers for the fronts when I use ZR1 wheels.....and none front or rear with the CCW's....

Christine,

It is a syncro trans.

J.R.

OK......I measured mine at home....built by CCW for the "standard" Camaro size (46mm offset I believe). The backspacing is 7 3/4". So it is likely you may have to run 1/4" spacers to get them to fit......the rear may be more forgiving however.

Randy,

Sent you an e-mail.

J.R.

JR,

I didn't realize I'd have to get a new bell housing and clutch set-up to make this work in #29. And that's too much for me to spend. I'm sorry! Best of luck selling your stuff and have a great time in the Corvette in two weeks.

Christine

Updated information and new parts added.

I ran a billet collar from Fortes Parts Connection to rotate the TKO 17* on the stock bellhousing and master/slave combo to make up for the 17* tilt of the T5 tranny, price, about $180 last time I checked a few years ago

Either way, it's very worth it.

Can I see pics and prices for the fiberglass dash, and the hubs
Thanks
Evan

Evan,

The dash and hubs are all part of the chassis/body package.

Sorry for the confusion.

J.R.