High Performance Handling Handbook by Don Alexander......
Chassis Engineering by Herb Adams..... SOLD
How To Make Your Car Handle by Fred Puhn........................Well used by not missing any pages no rips just used....................$10 each.....

Autocross Performance Handbook by Richard Newton....
Like new $SOLD

Think To Win by Don Alexander....$SOLD

Tune To Win by Carrol Smith.....SOLD

Step by step guide to Engine Blueprinting.....$10

How to Build the Smallblock Chevy.........$10

John Ligenfelter on modifying small block chevy engines.....like new save for one since flattened crease on corner of cover......$TEN BUCKS.

How to build and modify small block V8 cylinder heads....SOLD

Chevy TPI fuel injection swappers guide......like new....SOLD

Camaro Performance Handbook-performance modifications for 82-92 Camaro's....SOLD

Drive To Win by Carrol Smith. Like new-make an offer.

I'll take the bottom two.
Do you paypal?
thx,
jb

Is the cylinder head book the one by David Visard? if so I'll take it & the Herb Adams book. Eather way I take Herbs book.

Yeah the book is the David Vizard book....

sent pm's

Even if you are not swapping, that is a great book for learning about TPI.

Paypal sent.
Thanks Lon.

jb

Looking for 35 hp and 10 tq from a stock 305tpi easily. (future CMC2 for a 3rd gen? 260/310)
Slight cam and a little fuel pressure????????
Dunno.

A cam and headers should do that for you pretty easy. Can you tune the PCM? If not, that will be an issue though esp since your car is MAP based, right?

Payment sent for the Herb Adams & David Visard books.

No cam change for cmc unless it's a penut cam I think you can go to the 5 speed TPI cam. look for one from a 91-91 IB9 stick or L98 there the same. but check with the CMC guys first.

I'll take "Tune to Win".



Headers might put the TPI over on torque.

My motor makes 311HP / 317ft-lb at the rear wheels. Doesn't get much simpler then this.

.030 over 305
Stock crank
Eagle I-beam rods
Cast pistons - 11:1 compression
'113 AL Corvette heads (for weight, flow similarly to '083 TPI heads)
220/230 .502/.520 Comp hyd. roller cam
New GM LS1 lifters
Edelbrock Performer RPM intake
Holley 600DP carb
SLP 1 3/4" stainless shorty headers into a 3" Y-pipe with a Dynomax bullet on the end.

Peak power at ~6000RPM, 4000-6500 powerband.

The same motor with a TPI intake sucked for AI, but might be close for CMC2. Powerband was 3500-5000, maybe 5500 (TPI chokes it off). It definitely needed a tune. We got it OK to run, but never got it dialed in with the TPI.

Tune to Win already taken....sorry.....I'll edit the post above...

Did the books I bought get shipped?

Thanks.

Mike

Hello?

ditto on arethe books shipped?

Has anyone that bought books gotten them or heard anything?? This guy is a long-time member here so I doubt seriously that he's a scammer...but any more than one day without hearing from a seller after sending payment makes people nervous.

They are going out tomorrow....I usually ship things out through work. Good thing is it costs ME less, bad is that I don't always get free to get this taken care of.....I'll post office all the books tomorrow....

No worries, Lon. A little communication goes a long way!

Thanks for the update.

Mike

BTW a few books left.....Check above....A couple more added also.

So all the books went out on Friday the 20th then?

yep

Still no books...any way to track 'em?

Thanks.

Mike

They went out usps. Might take a few more days. They don't usually move things like UPS or fedex does....Don't sweat it man. I know you want your books....Sorry it's taking so long. If for some reason you never get them you would sure get your money back and then some.

On one's sweatin, my friend...we're good. You're obviously not someone who came on the board just to peddle some books...lol.

Got the books...they're in great condition. Thanks!!

Espcamaro; I got my books yesterday. thank you very much. I've been tring to get the head porting book for awhile now, It's ouy of print.
Terry