Parting out AIX Camaro - many parts - cheap - F-Body Road Racing and Autocross Forums

Parting out:

1994 Ex World Challenge Camaro
(floorpan and firewall spec'd to AIX)
all fiberglas or plastic panels except for rear quarter panels
full roll cage
fiberglas dash panel
lexan front and rear
2 hoods
wing plus rear spoiler
Currie 9 in rear end, currie axles (31 spline) with 3.50 9 in nodular rear 3rd member
brake lines with wilwood proportioning valve
alum. gas pedal with morse style throttle cable
new front hubs and steering rack
oil and water overflow tanks
two sway bars - through frame mounting
alum. radiator mount
custom carb air box
alum air dam
splitter
22 gal fuel safe cell with braided line to fuel pressure regulator
$4400

355 c.i. short block
3 hrs since freshened
$900 work of block work:
(decked, honed lifter bores, polished lifter valley, lifter return breather tubes,
honed out and champhered oil return holes, flat tappet oil restrictor plugs)
Eagle forged crank and H beam rods, JE pistons (flat top 5.4cc valve relief)
block decked to .035 quench area with .039 fel Pro gasket
custom flat tappet cam ( approx 244/248 deg .547/.555 lift at 0.050 on 108 deg LSA)
7 in depth double kickout pan
Cloyes double roller chain and sprocket, front timing cover
Moroso hi volume oil pump
clevite 77 bearings, JE rings
$1650

Tremec TKO 600 transmission
0.82 5th gear
3 hrs on trans
$1450 SOLD

Dual MSD 6AL boxes with 2 MSD coils and wiring
$275 SOLD

Complete Brembo brake setup (calipers) with alum hats & rotors (13 in front/ 12 in rear with front mounting brackets and braided lines)
1 almost new set of Hawk 9012 pads plus one spare set about 50% worn.
$1450

Jerico transmission - 4 speed
1.78 1st gear
need to check on other ratios
1.0 4th gear
$2100

Dr. Gas custom exhaust system:
SLP ceramic coated mid length headers (1 3/4") opened up to 3 in exit with custom dr. gas frame clearance tubes with x pipe and ovalized 3 in tubes that exit by rear of doors - due to x-pipe and ovalized tubes being one unit this system cannot be shipped. Must be picked up or delivered. May split up system if it does not sell as unit.
$575

wheels:
as a set only
Forgeline 2 piece wheelset
(2) 17 x 9.5 with 7 1/2 in backspacing, (2) 17 x 11.0 with 8 in backspacing with 275 x 40 front and 315 x 35 rear tires
$675 correction on backspacing of 17 x 9.5 wheels. SOLD

CCW classics (polished)
(2) 17 x 11 with 8 in backspacing, (2) 17 x 12 with 8 in backspacing, also comes with additional outside rims (2) to change 17 x 12's to 17 x 11's with 315 x 35 front and 335 x 30 rear tires
$1100 SOLD

(2) JRZ double adjustable coil overs for front of Camaro - will try to supply spring rate you want if I have them in my stock of springs.
$650. note - these list for $1350 each. SOLD

Tilton aluminum bellhousing with hydraulic throw out bearing
$140

Comp stainless roller rockers - for 3/8 in stud in 1.6 ratio - pro magnum model - not self aligning (i.e. requires guide plates)
$125 SOLD

More parts:
Stack Data Aquisition Guage model ST8100 ( this may be an M model as display indicated predicitve lap timing but without beacon I am not positive)
ser # 11631
with all wiring to senders/ignition. has low oil pressure warning light in unit.
and the following sending units:
water temp, oil pressure, fuel pressure
needs oil temp sender.
has lap time module and receiver but does not have transmitter beacon.
with manual
$675 (retail this unit with senders goes from $ 1700) SOLD

Griffin race radiator - 27.5 x 19 x 3 (2 row) -used for 1 race day. like new
with dual electric fans Griffin part # 55242X
$200 SOLD

Forgeline wheels (2) 17 x 9.5 - ( 7 1/2 in backspacing) 2 piece with 275x 40 x 17 DOT tires with approx 15 heat cycles. same price with or without tires. SOLD
$275

CCW classic polished wheels (2) 17 x 11 (7 1/2 in backspacing) 3 piece with 315 x 35 x 17 DOT tires with approx 6 heat cycles
used for one race season. same price with or without tires.
$ 675

Plus shipping

Please send all questions to consultjr@msn.com
or call me at 801-979-3739

Thanks,

J.R.

This post has been edited by JR-24: Jan 9 2008, 02:21 AM

JR-24 View Member Profile	Oct 29 2007, 10:07 PM Post #1
Member Group: Advanced Members Posts: 53 Joined: 25-January 04 From: Salt Lake City, UT Member No.: 153	Parting out: 1994 Ex World Challenge Camaro (floorpan and firewall spec'd to AIX) all fiberglas or plastic panels except for rear quarter panels full roll cage fiberglas dash panel lexan front and rear 2 hoods wing plus rear spoiler Currie 9 in rear end, currie axles (31 spline) with 3.50 9 in nodular rear 3rd member brake lines with wilwood proportioning valve alum. gas pedal with morse style throttle cable new front hubs and steering rack oil and water overflow tanks two sway bars - through frame mounting alum. radiator mount custom carb air box alum air dam splitter 22 gal fuel safe cell with braided line to fuel pressure regulator $4400 355 c.i. short block 3 hrs since freshened $900 work of block work: (decked, honed lifter bores, polished lifter valley, lifter return breather tubes, honed out and champhered oil return holes, flat tappet oil restrictor plugs) Eagle forged crank and H beam rods, JE pistons (flat top 5.4cc valve relief) block decked to .035 quench area with .039 fel Pro gasket custom flat tappet cam ( approx 244/248 deg .547/.555 lift at 0.050 on 108 deg LSA) 7 in depth double kickout pan Cloyes double roller chain and sprocket, front timing cover Moroso hi volume oil pump clevite 77 bearings, JE rings $1650 Tremec TKO 600 transmission 0.82 5th gear 3 hrs on trans $1450 SOLD Dual MSD 6AL boxes with 2 MSD coils and wiring $275 SOLD Complete Brembo brake setup (calipers) with alum hats & rotors (13 in front/ 12 in rear with front mounting brackets and braided lines) 1 almost new set of Hawk 9012 pads plus one spare set about 50% worn. $1450 Jerico transmission - 4 speed 1.78 1st gear need to check on other ratios 1.0 4th gear $2100 Dr. Gas custom exhaust system: SLP ceramic coated mid length headers (1 3/4") opened up to 3 in exit with custom dr. gas frame clearance tubes with x pipe and ovalized 3 in tubes that exit by rear of doors - due to x-pipe and ovalized tubes being one unit this system cannot be shipped. Must be picked up or delivered. May split up system if it does not sell as unit. $575 wheels: as a set only Forgeline 2 piece wheelset (2) 17 x 9.5 with 7 1/2 in backspacing, (2) 17 x 11.0 with 8 in backspacing with 275 x 40 front and 315 x 35 rear tires $675 correction on backspacing of 17 x 9.5 wheels. SOLD CCW classics (polished) (2) 17 x 11 with 8 in backspacing, (2) 17 x 12 with 8 in backspacing, also comes with additional outside rims (2) to change 17 x 12's to 17 x 11's with 315 x 35 front and 335 x 30 rear tires $1100 SOLD (2) JRZ double adjustable coil overs for front of Camaro - will try to supply spring rate you want if I have them in my stock of springs. $650. note - these list for $1350 each. SOLD Tilton aluminum bellhousing with hydraulic throw out bearing $140 Comp stainless roller rockers - for 3/8 in stud in 1.6 ratio - pro magnum model - not self aligning (i.e. requires guide plates) $125 SOLD More parts: Stack Data Aquisition Guage model ST8100 ( this may be an M model as display indicated predicitve lap timing but without beacon I am not positive) ser # 11631 with all wiring to senders/ignition. has low oil pressure warning light in unit. and the following sending units: water temp, oil pressure, fuel pressure needs oil temp sender. has lap time module and receiver but does not have transmitter beacon. with manual $675 (retail this unit with senders goes from $ 1700) SOLD Griffin race radiator - 27.5 x 19 x 3 (2 row) -used for 1 race day. like new with dual electric fans Griffin part # 55242X $200 SOLD Forgeline wheels (2) 17 x 9.5 - ( 7 1/2 in backspacing) 2 piece with 275x 40 x 17 DOT tires with approx 15 heat cycles. same price with or without tires. SOLD $275 CCW classic polished wheels (2) 17 x 11 (7 1/2 in backspacing) 3 piece with 315 x 35 x 17 DOT tires with approx 6 heat cycles used for one race season. same price with or without tires. $ 675 Plus shipping Please send all questions to consultjr@msn.com or call me at 801-979-3739 Thanks, J.R. This post has been edited by JR-24: Jan 9 2008, 02:21 AM

rmackintosh View Member Profile	Oct 29 2007, 10:33 PM Post #2
Senior Member Group: Advanced Members Posts: 5,226 Joined: 24-December 03 From: Danville, CA, USA Member No.: 27	I am interested in: all fiberglas or plastic panels == are they fiberglass nose and fenders? wing plus rear spoiler == is it a current/modern SWCGT wing style, or just a spoiler? Currie 9 in rear end, currie axles (31 spline) with 3.50 9 in nodular rear 3rd member ==is it a full floater? any more details.... splitter == any pics of this? CCW wheels == what size, style, color

rmackintosh View Member Profile	Oct 30 2007, 07:48 PM Post #3
Senior Member Group: Advanced Members Posts: 5,226 Joined: 24-December 03 From: Danville, CA, USA Member No.: 27	QUOTE (rmackintosh @ Oct 29 2007, 05:33 PM) I am interested in: CCW wheels == what size, style, color You say 8 inch backspacing. When I bought mine they called the offset 46mm I believe. Are these the same? Otherwise I have to go measure mine at home....

rmackintosh View Member Profile	Oct 31 2007, 06:31 AM Post #4
Senior Member Group: Advanced Members Posts: 5,226 Joined: 24-December 03 From: Danville, CA, USA Member No.: 27	QUOTE (rmackintosh @ Oct 30 2007, 02:48 PM) QUOTE (rmackintosh @ Oct 29 2007, 05:33 PM) I am interested in: CCW wheels == what size, style, color You say 8 inch backspacing. When I bought mine they called the offset 46mm I believe. Are these the same? Otherwise I have to go measure mine at home.... OK......I measured mine at home....built by CCW for the "standard" Camaro size (46mm offset I believe). The backspacing is 7 3/4". So it is likely you may have to run 1/4" spacers to get them to fit......the rear may be more forgiving however.