[roostmeyer]

Adding a few other parts...

BMR tranny mounted torque arm $160

(IMG:http://i405.photobucket.com/albums/pp135/roostmeyer/parts%20for%20sale/th_photobucket-6446-1327453156930.jpg)

Going to offset control arms, so I won't need these any more. Rubber bushed ends on one side to control NVH (while still being much stiffer than stock), custom spacers, and 3/4" to 1/2" ID XMR QA1 rod ends with sealsit to keep the rod ends clean. I'm going to offset LCA's to go with my expande rear fenderwells. $110, you can't build them for this...

http://www.summitracing.com/parts/HAL-XMR8-12/
http://www.howeracing.com/p-7603-rubber-bushing-joint.aspx

(IMG:http://i405.photobucket.com/albums/pp135/roostmeyer/parts%20for%20sale/th_photobucket-2235-1327453140041.jpg)

SOLD All Star rear jacks $80 new, hows $45+ shipping sound? They have(soon to be had) 3 3/4" long welds on each to hold them to the axle, The adjusters have been tapped for a set screw and painted. No rust, not a lot of time on them...
http://pitstopusa.com/i-5066715-allstar-pe...juster-nut.html

900lb/in 11x5.5 Hypercoil, $88 new, $45, found out the hard way these are too short, but I'm guessing you could cut the first 1/4 coil and use them for weigh jacks.
http://pitstopusa.com/i-5069276-hypercoils...o-d-900-lb.html

SOLD 1200lb/in 11x5.5 Hypercoil, $88 new, $50 ~1/4 coil cut from each, Nice and low on my car with an lt1. Still on the car, It will probably be a month+ before I get to changing them out, so just checking interest I suppose.

250lb/in 8x5 Landrum springs $108 new, $60.
http://www.landrumspring.com/pages/coilspr...mp;pagenumber=1

300lb/in 8x5 Susp. spec. springs. $88 new, $50.
http://pitstopusa.com/c-134778-springs-rea...d-x-8-tall.html

150b/in 12x5/pigtail hypercoil $88 new, $50 Drop in rear spring with the stock isolators. Pretty low without...
http://pitstopusa.com/i-5069261-hypercoils...-appearing.html

I also have front IROC springs, the 707lb/in 5664 p/n. I think I took off 1/4 or a 1/3 of a coil, just enough for some slight lowering. $40
Everything is in good shape, no rust, good shape or as described. Its all OBO and plus shipping. Let me know if your interested and I'll snap some photos as I go.

BMR tranny mounted torque arm $160

(IMG:http://i405.photobucket.com/albums/pp135/roostmeyer/parts%20for%20sale/th_photobucket-6446-1327453156930.jpg)

Custom lower control arms, rubber bushed ends on one side (Much stiffer than stock) and 3/4" to 1/2" ID XMR QA1 rod ends with sealsit to keep the rod ends clean. $120, you can't build them for this...

http://www.summitracing.com/parts/HAL-XMR8-12/
http://www.howeracing.com/p-7603-rubber-bushing-joint.aspx

(IMG:http://i405.photobucket.com/albums/pp135/roostmeyer/parts%20for%20sale/th_photobucket-2235-1327453140041.jpg)

This post has been edited by roostmeyer: Jan 25 2012, 02:32 AM