IPB

Welcome Guest ( Log In | Register )

Unbalanced EngineeringBlaine Fabrication.comUMI PerformanceHotpart.comSolo Performance
> Welcome to the "I need new intake rockers" garage sale
Racerdad916
post Nov 5 2014, 12:20 AM
Post #1


Full NVH
**

Group: Moderators
Posts: 444
Joined: 16-July 07
From: Grove City, Ohio
Member No.: 1,854



Welcome to the "I need new intake rocker arms" garage sale. I recently broke an intake rocker on my Jesel set-up (way too old with way to much spring pressure)and I thought
I'd get rid of the parts left over from the Camaro project. I'll attempt to add pics, or I can send pics if needed. Shipping will be actual UPS ground or local pick-up. If you think
the price is high, make me an offer. Remember, you are helping fund another racer's project!

SOLD!!!-12 gallon PLASTIC red Harwood fuel cell (drag style), no mounting brackets, no foam, has plumbing fittings, cleaned and leak tested. $50
SOLD!!!
33mm 3rd Gen F-body Hollow Hellwig sway bar with hardware (New) $100
Kirkey 10 degree layback circle track seat, blue tweed cover, 16"wide, w/sliders, good condition. $75
Butlerbuilt 20 Layback circle track seat, red cloth cover (faded, some wear) fair condition. $75
SOLD!!!Used MSD 6A ignition box, used, worked when removed from my Camaro. $50
(16) Comp Cams stock length, SBC, 5/16" Magnum pushrods, part number 7372, nearly new. $50
New SBC long water pump (Advance Auto brand) $15
Under-drive crank and alternator pulleys for a 6 rib serpentine belt (long water pump, I think), stock crank pulley and smooth water pump pulley
(these are from an LTI car) $40 for the pulley pile (IMG:http://www.frrax.com/rrforum/style_emoticons/default/burnout.gif)
Holley HP 830 with repaired base plate, jetted to your specs or I can put it back to stock Holley calibration, 50cc front acc pump kit $375
4 panel circle track rear view mirror $25
Wilson 1" aluminum carb spacer, changeable from open to 4 hole. 4150 flange. $40
4150 to 4500 Holley 2" carb spacer $40
3/4" Mr Gasket aluminum Quadra-jet to 4150 flange adapter $10
East Coast Electric 1 wire alternator for SBC 70amp output, comes with a 6 rib GO FAST CHROME fan and pulley. Nearly new, has a few hundred miles on it. $40
(2) SBC GO FAST CHROME t-stat housings, (1) straight, (1) driver side offset $10
New Jegs adjustable fuel pressure regulator (carb only)
3rd Gen F-body clutch pedals with aluminum pedal pads $75
Attached File(s)
Attached File  Billy_parts.jpg ( 87.35K ) Number of downloads: 10
 
Go to the top of the page
 
+Quote Post
 
Start new topic
Replies
Racerdad916
post Nov 6 2014, 06:51 AM
Post #2


Full NVH
**

Group: Moderators
Posts: 444
Joined: 16-July 07
From: Grove City, Ohio
Member No.: 1,854



IIRC, mine are .180 offset. That looks like SB2 stuff... my stuff is old school 23 degree... the best 1999 had to offer!
Go to the top of the page
 
+Quote Post

Posts in this topic
Racerdad916   Welcome to the "I need new intake rockers" garage sale   Nov 5 2014, 12:20 AM
Shortcutsleeping   I just swapped heads on my car and pulled off a se...   Nov 5 2014, 05:34 PM
Shortcutsleeping   My busy Friday evening... Costas cars and such...   Nov 5 2014, 05:41 PM
Racerdad916   IIRC, mine are .180 offset. That looks like SB2 st...   Nov 6 2014, 06:51 AM
Shortcutsleeping   Double check your offset, these are .450 from earl...   Nov 6 2014, 06:58 PM
Racerdad916   I'm sure yours are longer than my 23 degree st...   Nov 6 2014, 07:12 PM
Shortcutsleeping   My intake lifters are offset .180 inch. They worke...   Nov 6 2014, 08:34 PM
Racerdad916   Mine are definitely around .180 offset. I'll m...   Nov 7 2014, 06:46 AM
Shortcutsleeping   QUOTE (Racerdad916 @ Nov 7 2014, 12:46 AM...   Nov 7 2014, 04:44 PM
trackbird   I believe his heads use the "60/40" valv...   Nov 7 2014, 08:01 PM
Racerdad916   I spoke to my cylinder head guy today, the .450 of...   Nov 8 2014, 03:46 AM
Shortcutsleeping   Well, it was worth a shot. I use the .450 rocker ...   Nov 8 2014, 04:27 AM
Racerdad916   MSD box is sold...   Nov 9 2014, 12:36 PM
Racerdad916   pics added to the original post...   Nov 11 2014, 02:54 PM
NOT A TA   Received the MSD box, will test in one of the cars...   Nov 13 2014, 09:29 PM
Racerdad916   If there is an issue, let me know..   Nov 14 2014, 03:28 PM
Racerdad916   I just found a 23mm (?) Rear sway bar with bracket...   Nov 27 2014, 10:44 PM

« Next Oldest · Classifieds · Next Newest »
 

Reply to this topicStart new topic
2 User(s) are reading this topic (2 Guests and 0 Anonymous Users)
0 Members:

 



Lo-Fi Version Time is now: 1st May 2025 - 08:41 PM