|
||||
Apr 5 2017, 09:38 PM
Post
#1
|
|
|
Experienced Member ![]() ![]() ![]() Group: Advanced Members Posts: 2,038 Joined: 3-March 10 From: Huntersville, NC Member No.: 9,105 |
What a PITA. Ok so I haven't cut any lines yet. But I really do want to try to get this thing by installed tomorrow. But at the same time, I don't want to have a problem that I can't fix before I have to leave Friday for the track.
The rear line is a single 1/4" line. So I need to cut the rear line that's under the car, add a fitting and flare it then connect another one to it, run it through the trans tunnel and mount it in the ash tray location. Obviously then back down again and connect to the rear of the brake line that runs to the rear. I've rented a flare tool before and it took me a couple of tries but I got it to seal. I'm afraid of cutting the rear line clean enough and making a good flare. I feel like that could be a disaster. Also, will I have a hard time bleeding the brakes with the prop. valve being mounted up so high? I might just scrap this for now since I have a track day coming up. Any help will be appreciated! |
|
|
|
![]() |
Apr 6 2017, 04:56 AM
Post
#2
|
|
|
Member ![]() Group: Advanced Members Posts: 240 Joined: 19-January 12 Member No.: 141,541 |
Anyways to answer your question, it is a "1/4" size line but usually it is metric bubble line on both ends. You can try use a regular double flare as this is how mine was setup originally (bias valve mounted in bay connected to stock line with remote wilwood cable). I'm not sure if having you valve up high in the ash tray (close to trans tunnel?) would be an issue for bleeding as long as it is lower than the master cylinder; usually a pressure bleeder would make quick work of that.
I don't recall the stock line being very easy to flare compared to aftermarket line you can buy when making your own lines. To do it right, IMO, I would rip out the stock line and run it through the cabin as 3/16 line with adapters front/rear. This post has been edited by Pranav: Apr 6 2017, 04:57 AM |
|
|
|
Steve91T Adding a Wilwood proportioning valve.... Apr 5 2017, 09:38 PM
trackbird Why are you putting a valve in it? Are you having ... Apr 5 2017, 11:35 PM
Pranav Yep, I have a bias valve but don't even use it... Apr 6 2017, 12:03 AM
Steve91T I've removed abs, that transfered way too much... Apr 6 2017, 12:55 AM
trackbird Ah, I thought the ABS system was still in the car. Apr 6 2017, 01:25 AM
CrashTestDummy That's a double flare tool, right? These days... Apr 6 2017, 02:36 AM
Pranav Have you done the necessary fixes to stop axle hop... Apr 6 2017, 04:25 AM
Steve91T QUOTE (Pranav @ Apr 6 2017, 12:25 AM) Hav... Apr 6 2017, 04:34 AM
Pranav Strange. I'm currently running XP10s up front,... Apr 6 2017, 04:52 AM
Racerdad916 QUOTE (Pranav @ Apr 6 2017, 12:56 AM) Any... Apr 6 2017, 11:50 AM
GCrites80s So the consensus seems to be, don't install a ... Apr 6 2017, 09:27 PM
trackbird QUOTE (GCrites80s @ Apr 6 2017, 05:27 PM)... Apr 6 2017, 09:34 PM
KCG QUOTE (trackbird @ Apr 6 2017, 05:34 PM) ... May 25 2017, 10:36 AM
Steve91T I just checked my rear brakes. The pads are gone. ... Apr 6 2017, 10:35 PM
BryanL QUOTE (Steve91T @ Apr 6 2017, 05:35 PM) I... Apr 7 2017, 03:30 PM
JimMueller I installed a Wilwood dial BPV between the reservo... Apr 8 2017, 10:59 PM
Eugenio_SS I also got rid of abs and put the proportioning va... May 23 2017, 07:29 PM![]() ![]() |
| Lo-Fi Version | Time is now: 21st November 2026 - 11:11 AM |