 Oil cooler help LT1 |
|
|||||||||
 Jan 10 2016, 05:01 PM
Post
#1
|
|
|
Experienced Member  Group: Advanced Members Posts: 2,038 Joined: 3-March 10 From: Huntersville, NC Member No.: 9,105  |
Hey guys. I have some questions about oil coolers.
How do I plum to the engine? I'm using a sandwich adapter for oil pressure and temp. There are two unused ports in that adapter. Can I use those for the oil cooler? One of those ports would be for the supply, but where does the return go? It's an LT1 with a Moroso pan. My other question is are there any problems with mounting the cooler above the engine in the hood scoop? I'm planning on securin the lines to the bottom of the hood and run them down the drivers side hinge then to the engine. I can't imagine there would be any problems with the location, but I thought I'd ask in case you guys know something I don't. I'm not going to run a thermostat for the oil. I'm just going to tape the back side of the cooler for street use. |
 |
 
|
 |
Replies
|
Apr 7 2016, 01:09 AM
Post
#2
|
|
|
Experienced Member Group: Advanced Members Posts: 2,038 Joined: 3-March 10 From: Huntersville, NC Member No.: 9,105 |
(IMG:http://img.photobucket.com/albums/v199/Steve91T/Camaro/C5ACE7F4-5ECC-40EC-8C89-11AB4A159E60.jpg)
I was so excited to get the oil cooler installed when....the adapter doesn't fit. The diameter is too small. I tried to get the adapter to thread just for the hell of it and I couldn't. But then again, I didn't try too hard. I'll try again when I change the oil I an a few days after I cook this oil to over 300 degrees. Better yet, I'll call canton and have them send me the correct one. |
|
|
|
 Apr 17 2016, 06:15 AM
Post
#3
|
|
|
newbie Group: Members Posts: 10 Joined: 4-February 07 From: Eldersburg MD Member No.: 1,648 |
QUOTE (Steve91T @ Apr 7 2016, 01:09 AM)  (IMG:http://img.photobucket.com/albums/v199/Steve91T/Camaro/C5ACE7F4-5ECC-40EC-8C89-11AB4A159E60.jpg) I was so excited to get the oil cooler installed when....the adapter doesn't fit. The diameter is too small. I tried to get the adapter to thread just for the hell of it and I couldn't. But then again, I didn't try too hard. I'll try again when I change the oil I an a few days after I cook this oil to over 300 degrees. Better yet, I'll call canton and have them send me the correct one. It will def keep your oil cooler than 300 I take it Canton didnt take notes again lol LT4 Cooler worked for me same as c4 vette late lt4 cooler i think but don't entirely remember. It would make sense if they were. I can imagine they designed a pan in the 90's for a LT4 corvette first. EDIT: LT4 optioned cars This post has been edited by CamaroRick: Apr 19 2016, 10:06 PM |
|
|
|
Posts in this topic
Steve91T Oil cooler help LT1 Jan 10 2016, 05:01 PM
79T/A I'm assuming LT1 style ss hood? I don't th... Jan 10 2016, 11:17 PM
Steve91T QUOTE (79T/A @ Jan 10 2016, 06:17 PM) I... Jan 11 2016, 01:01 AM CrashTestDummy Interesting idea, but I think you'll be spendi... Jan 12 2016, 04:00 PM Steve91T I guess I'll be the first to try it. If it doe... Jan 12 2016, 06:10 PM KCG QUOTE (Steve91T @ Jan 12 2016, 01:10 PM) ... Jan 12 2016, 10:37 PM Steve91T QUOTE (KCG @ Jan 12 2016, 05:37 PM) QUOTE... Jan 13 2016, 01:34 AM DAlgozine My opinion, I wouldn't put attached the oil co... Jan 13 2016, 04:13 PM Steve91T QUOTE (DAlgozine @ Jan 13 2016, 11:13 AM)... Jan 13 2016, 04:36 PM DAlgozine QUOTE (Steve91T @ Jan 13 2016, 10:36 AM) ... Jan 13 2016, 08:36 PM Steve91T I'll scrap the idea. Maybe I'll try for so... Jan 13 2016, 08:19 PM DAlgozine Here is a photo of a sandwich type for an LT1 with... Jan 13 2016, 08:44 PM Steve91T Hey thanks for the help. I need to look at my adap... Jan 20 2016, 05:28 PM Steve91T This is what Canton sells for the LT1. They said i... Feb 23 2016, 08:36 PM CrashTestDummy You might be able to get an old oil cooler line as... Feb 23 2016, 10:03 PM Steve91T Interesting. I'll have to look into that. I r... Feb 23 2016, 10:43 PM Steve91T http://m.summitracing.com/parts/ear-510erl
Would ... Feb 24 2016, 01:37 PM Blainefab QUOTE (Steve91T @ Feb 24 2016, 05:37 AM) ... Mar 2 2016, 03:41 AM Steve91T QUOTE (Blainefab @ Mar 1 2016, 10:41 PM) ... Mar 2 2016, 12:19 PM Steve91T Anyone know if that adapter will work? I think it... Feb 26 2016, 01:12 AM nape If you're going to replace the engine later th... Feb 28 2016, 08:22 PM Steve91T QUOTE (nape @ Feb 28 2016, 03:22 PM) If y... Feb 28 2016, 08:57 PM nape QUOTE (Steve91T @ Feb 28 2016, 02:57 PM) ... Feb 29 2016, 12:20 AM CrashTestDummy Changing the oil often is a great recommendation. ... Feb 28 2016, 09:18 PM Steve91T One thing I didn't mention is I have an unused... Feb 29 2016, 01:44 AM CrashTestDummy Oil, or water temps? Feb 29 2016, 03:43 AM Steve91T QUOTE (CrashTestDummy @ Feb 28 2016, 10:4... Feb 29 2016, 04:15 AM mr.beachcomber QUOTE (Steve91T @ Feb 29 2016, 04:15 AM) ... Mar 1 2016, 01:28 PM CrashTestDummy 300, wow. I thought I read somewhere, and absolut... Mar 2 2016, 01:59 AM Steve91T Well my oil pan pre heater works well. The oil tem... Mar 14 2016, 01:25 AM bubba353z QUOTE (Steve91T @ Mar 13 2016, 09:25 PM) ... Mar 14 2016, 04:30 PM Steve91T QUOTE (bubba353z @ Mar 14 2016, 12:30 PM)... Mar 14 2016, 04:53 PM Blainefab QUOTE (Steve91T @ Mar 14 2016, 09:53 AM) ... Mar 14 2016, 10:43 PM Steve91T QUOTE (Blainefab @ Mar 14 2016, 06:43 PM)... Mar 15 2016, 02:54 PM Steve91T So tonight I loosed the Y pipe and wrapped the y p... Apr 1 2016, 12:32 AM mr.beachcomber QUOTE (Steve91T @ Apr 1 2016, 12:32 AM) .... Apr 1 2016, 01:00 PM Steve91T QUOTE (mr.beachcomber @ Apr 1 2016, 09:00... Apr 1 2016, 03:00 PM mr.beachcomber QUOTE (Steve91T @ Apr 1 2016, 03:00 PM) .... Apr 2 2016, 03:39 PM nape What were the water temps? Where is your oil temp ... Apr 1 2016, 03:15 AM Steve91T QUOTE (nape @ Mar 31 2016, 11:15 PM) What... Apr 1 2016, 03:20 AM Steve91T My oil press is 60 psi at 2000 rpm when hot. Almos... Apr 1 2016, 10:24 PM Steve91T That's a huge help. Thank you for taking the t... Apr 2 2016, 03:58 PM mr.beachcomber QUOTE (Steve91T @ Apr 2 2016, 03:58 PM) .... Apr 3 2016, 01:23 PM Steve91T http://m.summitracing.com/parts/ctr-22-726
I... Apr 2 2016, 05:18 PM Steve91T Actually I think this is the thread pitch I need. ... Apr 2 2016, 05:25 PM mr.beachcomber QUOTE (Steve91T @ Apr 2 2016, 05:25 PM) A... Apr 3 2016, 01:20 PM Steve91T QUOTE (mr.beachcomber @ Apr 3 2016, 09:20... Apr 3 2016, 01:45 PM mr.beachcomber Obviously not thinking when I answered your post a... Apr 3 2016, 10:16 PM Steve91T QUOTE (mr.beachcomber @ Apr 3 2016, 06:16... Apr 4 2016, 12:37 AM slowTA http://www.wixfilters.com
The wix filter look up ... Apr 4 2016, 01:12 AM mr.beachcomber QUOTE (CamaroRick @ Apr 17 2016, 06:15 AM... Apr 18 2016, 12:37 PM CamaroRick QUOTE (mr.beachcomber @ Apr 18 2016, 12:3... Apr 19 2016, 10:01 PM CamaroRick QUOTE (Steve91T @ Jan 10 2016, 05:01 PM) ... Apr 17 2016, 05:53 AM CamaroRick RE: Oil cooler help LT1 Apr 17 2016, 06:48 AM Steve91T This is what I'm dealing with. I'm screwin... Apr 18 2016, 02:37 PM mr.beachcomber QUOTE (Steve91T @ Apr 18 2016, 02:37 PM) ... Apr 18 2016, 04:41 PM Steve91T QUOTE (mr.beachcomber @ Apr 18 2016, 12:4... Apr 18 2016, 06:36 PM Steve91T http://m.summitracing.com/parts/ctr-22-541
Just sp... Apr 18 2016, 06:47 PM Blainefab Replace the block adapter too - that part that has... Apr 19 2016, 02:28 AM Steve91T QUOTE (Blainefab @ Apr 18 2016, 10:28 PM)... Apr 19 2016, 06:28 PM Steve91T I finally got started installing my oil cooler tod... Apr 23 2016, 02:55 AM Steve91T It's done!
My first attempt at making li... Apr 27 2016, 01:33 AM Steve91T There's a lot more room between the oil cooler... Apr 27 2016, 01:35 AM Steve91T So today I had a chance to take the Camaro to Targ... Apr 28 2016, 11:43 PM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
| Lo-Fi Version | Time is now: 22nd June 2025 - 12:22 AM |