IPB

Welcome Guest ( Log In | Register )

 Forum Rules 
Hotpart.comSolo PerformanceBlaine Fabrication.comUMI PerformanceUnbalanced Engineering
> As I sit here with a Vicadin buzz...., Safety!
bsim
post May 24 2005, 04:42 AM
Post #1


Race Driver
**

Group: Advanced Members
Posts: 382
Joined: 14-February 04
From: SoCal
Member No.: 205



So I'm sitting at home, out of work for a few days eating Vicadin...

Yesterday I was cutting some 1/8" x 3"w steel into some lengths soon to be seat mounts. On my last cut, a piece of steel made it around my glasses and under my eyelid, whereupon it decided to lodge itself. OW.

5 hours later (after extended waits at both an urgent care AND the ER, the piece was finally removed. Bottom line, I have a severely 'abrased' cornea, to go along with one pretty good 'cut'. Thankfully, the cornea heals quickly, so as long as I don't get infected, I should be fine in a few days.

So, just a reminder, if you don't have safety goggles, get 'em. Make sure that they provide good 'seals' around your eyes - the one's I had on left a small gap, and it was enough to let a piece through.

Interestingly, the eye doctor mentioned he's seen cases where goggles were worn, the guy got done working, and later in the evening a piece that had stuck in his hair fell down and into his eye.

Honestly, that was the WORST PAIN I've felt in my 38 years - I wouldn't wish it on anyone - not even Al.
Go to the top of the page
 
+Quote Post
 
Start new topic
Replies
JonV
post May 24 2005, 10:17 PM
Post #2


Member
*

Group: Advanced Members
Posts: 143
Joined: 4-January 04
From: Sarnia
Member No.: 97



QUOTE (AllZWay @ May 24 2005, 10:13)
Luckily the eye heals quickly, so maybe you will feel much better soon.

:




Tell my wife that will you. She got a paper cut in her eye last year in March and it still hasn't healed properly. It's very painful. (IMG:http://www.frrax.com/rrforum/style_emoticons/default/blink.gif)
Go to the top of the page
 
+Quote Post

Posts in this topic
bsim   As I sit here with a Vicadin buzz....   May 24 2005, 04:42 AM
rmackintosh   I had a similar experience one time...IT WAS HELL ...   May 24 2005, 05:09 AM
mitchntx   Grinding dust goes everywhere ... If you have and...   May 24 2005, 10:20 AM
pknowles   I feel your pain. In 2000 I was fabricating a ram...   May 24 2005, 12:06 PM
98_1LE   Ouch. I hope you heal quickly. This must be pain ...   May 24 2005, 03:51 PM
AllZWay   That does sound painfull. Luckily the eye heals q...   May 24 2005, 04:13 PM
CMC #37   Dude, you must be on drugs - its Vicodin! Get...   May 24 2005, 05:06 PM
prockbp   when you're cutting/grinding w/ abbrasive mate...   May 24 2005, 07:12 PM
JonV   QUOTE (AllZWay @ May 24 2005, 10:13)Luckily t...   May 24 2005, 10:17 PM
CrashTestDummy   QUOTE (bsim @ May 23 2005, 22:42)Interestingl...   May 24 2005, 10:49 PM
CMC #37   As I told Brad on the CMC board, hubby had this ha...   May 25 2005, 12:24 AM
94bird   Sorry to hear about what happened, but I'm ano...   May 25 2005, 01:24 AM
bobbylee   I can't stand those goggles that cover your ey...   May 25 2005, 04:22 AM
v7guy   sorry to hear about that man, I've been there ...   May 25 2005, 03:47 PM
slowTA   I haven't had anything too bad get in my eyes,...   May 26 2005, 12:12 AM

« Next Oldest · General Discussion · Next Newest »
 

Reply to this topicStart new topic
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:

 



Lo-Fi Version Time is now: 7th June 2025 - 12:54 PM